Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 90 Oscillator question
#2

Hi Mark,
I think the general consensus is that original was 38g but I don't think that gauge is real important within reason. Direction is, wind it the wrong way around and it won't oscillate. Not enough turns will stop it from working, if you are close to the number of turns it may work but won't tune the whole range of frequencies. Will dropout at the low end of the band. Some will bake the coil at low temp to evaporate any moisture in the form. Water can drastically lower the Q of the coil (efficiency).
If you are sure you are winding in the proper direction then try adding a few more turns (like 3-4) and see if that snaps it back into operation. You can take a listen for it with another set tuned to the same frequency + the IF frequency.

GL
Terry


Messages In This Thread
Philco 90 Oscillator question - by bdi1976 - 03-07-2016, 10:00 PM
RE: Philco 90 Oscillator question - by Radioroslyn - 03-08-2016, 07:32 AM
RE: Philco 90 Oscillator question - by TV MAN - 03-10-2016, 10:31 AM
RE: Philco 90 Oscillator question - by bdi1976 - 03-11-2016, 09:54 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-18-2017, 01:51 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-18-2017, 07:00 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-19-2017, 12:35 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-20-2017, 10:03 PM
RE: Philco 90 Oscillator question - by sam - 02-21-2017, 12:42 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-21-2017, 05:24 PM
RE: Philco 90 Oscillator question - by bdi1976 - 02-24-2017, 10:38 PM
RE: Philco 90 Oscillator question - by bdi1976 - 03-12-2017, 05:11 PM
RE: Philco 90 Oscillator question - by bdi1976 - 03-12-2017, 07:54 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Well, maybe - maybe not  :lol: It's been an interesting project so far! Something so simple, yet so cranky. The 1st one ...TV MAN — 05:12 PM
1949 Motorola 5A9M
Haven't thought of Burgess batteres in a while  https://www.radionostalgia.ca/lib/Images/battery/us/burgess1D.jpgi ...Vlad95 — 03:50 PM
Philco Model 16 wiring question
Measure the voltages first, just in case.morzh — 02:19 PM
1949 Motorola 5A9M
Haven't thought of Burgess batteries in a while Mr. Fixer. Boston Edison always used Burgess in their Bright Star yellow...Paul Philco322 — 02:17 PM
1949 Motorola 5A9M
Thanks Sam. I'll let you know. I can probably scare some up from the local radio club.klondike98 — 02:07 PM
Philco 89 Code 123 Osc Coil
Hello,  I thought I would post my findings on my bad oscillator tickler coil. There were 27 turns on the outer coil b...dconant — 12:38 PM
Philco Model 16 wiring question
Thanks Morzh. So it appears I did wire it incorrectly and I have to switch the wires between pins 2 and 4.bobclausen — 09:24 AM
Philco 46-1209 strange behavior
No, it's not a problem, just during certain condition it could show up. Yes, an internal tube short could do that too. ...morzh — 09:13 AM
HiFi (Chifi) tube amp build - but my own design.
You sound guys are never satisfied. :crazy: :clap:RodB — 09:10 AM
HiFi (Chifi) tube amp build - but my own design.
I got some new ceramic octal tube sockets installed and also tried some different coupling caps.  The results:  The go...TV MAN — 08:42 AM

[-]
Who's Online
There are currently 993 online users. [Complete List]
» 1 Member(s) | 992 Guest(s)
Avatar

>