Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA 28x5 help
#3

Paul,
Thanks for the help. I haven't bought the radio yet, but want to. Hoping the speaker is original.
Steve


Messages In This Thread
RCA 28x5 help - by SteveG - 03-17-2016, 08:46 PM
RE: RCA 28x5 help - by Paul Philco322 - 03-17-2016, 09:19 PM
RE: RCA 28x5 help - by SteveG - 03-17-2016, 10:14 PM
RE: RCA 28x5 help - by Paul Philco322 - 03-18-2016, 04:32 PM
RE: RCA 28x5 help - by Joe Rossi - 03-19-2016, 09:03 AM
RE: RCA 28x5 help - by SteveG - 03-18-2016, 04:59 PM
RE: RCA 28x5 help - by SteveG - 03-19-2016, 06:57 PM
RE: RCA 28x5 help - by SteveG - 03-26-2016, 06:29 PM
RE: RCA 28x5 help - by Arran - 03-27-2016, 04:24 AM
RE: RCA 28x5 help - by KCMike - 03-26-2016, 10:27 PM
RE: RCA 28x5 help - by SteveG - 03-27-2016, 12:32 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM
Philco 60 Squealing
Your IF transformers are tuned to the resonant frequency they were designed for. When you observe the bell curve they di...RodB — 01:35 PM
identify very thin wire for replacement on 37-640
Thanks so much for your help!  I really could not have gotten this far without the kindness of you and other members.  T...georgetownjohn — 11:50 AM
Philco 38-7 Oscillation
Will do, thank you.tludka — 10:26 AM
Philco 38-7 Oscillation
As to your oscillation issue I would align the IF transformers. That may solve the problem. You also would want to check...Radioroslyn — 10:22 AM

[-]
Who's Online
There are currently 3198 online users. [Complete List]
» 4 Member(s) | 3194 Guest(s)
AvatarAvatarAvatarAvatar

>