40-150 No SW

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

40-150 No SW

gregb
Senior Member

Posts: 599
Threads: 24
Joined: Jan 2014
City: Edmonton AB CA

03-28-2016, 10:07 PM

Well I just reinstalled the coil after baking at 150 deg for about an hour an a half, no change. The coils all ohm out ok and the switches are all wired right and still no shortwave. I think I have to put this one aside for a while.

Gregb

Find

« Next Oldest | Next Newest »

Messages In This Thread

40-150 No SW - by gregb - 03-26-2016, 04:18 PM

RE: 40-150 No SW - by pbert - 03-26-2016, 06:03 PM

RE: 40-150 No SW - by klondike98 - 03-26-2016, 06:19 PM

RE: 40-150 No SW - by gregb - 03-26-2016, 08:35 PM

RE: 40-150 No SW - by gregb - 03-28-2016, 12:01 AM

RE: 40-150 No SW - by David - 03-28-2016, 09:04 PM

RE: 40-150 No SW - by gregb - 03-28-2016, 10:07 PM

RE: 40-150 No SW - by Arran - 03-29-2016, 03:47 AM

RE: 40-150 No SW - by gregb - 03-29-2016, 08:55 AM

RE: 40-150 No SW - by Ron Ramirez - 03-29-2016, 05:50 AM

RE: 40-150 No SW - by gregb - 03-29-2016, 08:56 AM

RE: 40-150 No SW - by fifties - 03-29-2016, 08:54 PM

RE: 40-150 No SW - by gregb - 03-29-2016, 09:05 PM

RE: 40-150 No SW - by Raleigh - 04-13-2016, 12:39 AM

RE: 40-150 No SW - by gregb - 04-13-2016, 09:10 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

Who's Online

There are currently 3290 online users. [Complete List]
» 1 Member(s) | 3289 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me