1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 40-190 Humming Along?
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

04-06-2016, 08:17 PM
Welcome to the Phorum!
Icon_wave

Just a thought... you might swap out that 20uF electrolytic from the previous repair.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 40-190 Humming Along? - by Mike Schettler - 04-06-2016, 07:41 PM
RE: Philco 40-190 Humming Along? - by klondike98 - 04-06-2016, 08:17 PM
RE: Philco 40-190 Humming Along? - by Radioroslyn - 04-06-2016, 08:34 PM
RE: Philco 40-190 Humming Along? - by fifties - 04-06-2016, 10:59 PM
RE: Philco 40-190 Humming Along? - by Radioroslyn - 04-07-2016, 08:43 PM
RE: Philco 40-190 Humming Along? - by fifties - 04-09-2016, 07:37 PM
RE: Philco 40-190 Humming Along? - by KCMike - 05-13-2016, 09:19 PM
RE: Philco 40-190 Humming Along? - by morzh - 05-14-2016, 07:33 PM
RE: Philco 40-190 Humming Along? - by klondike98 - 05-14-2016, 06:56 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

[-]
Who's Online
There are currently 4568 online users. [Complete List]
» 3 Member(s) | 4565 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration