Crosley 10-136

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Crosley 10-136

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

04-09-2016, 09:34 AM

Good morning

I have a Crosley 10-136 http://www.nostalgiaair.org/Resources/172/M0003172.htm

I have recapped it and it plays but there is a problem with the Vol so I thought I need to check it out especially since it looks as though it has been replaced. The Pot Resistance show 500k the Print shows it should be 3 meg and a tap at 300k ( parts list). I googled 3meg pot and the highest I see is 1meg and see no tap. Any suggestions on what to do? I have a couple of sites to try yet but I'm not hopeful. Thanks

Eric

Find

« Next Oldest | Next Newest »

Messages In This Thread

Crosley 10-136 - by Eric - 04-09-2016, 09:34 AM

RE: Crosley 10-136 - by Radioroslyn - 04-09-2016, 10:32 AM

RE: Crosley 10-136 - by Eric - 04-09-2016, 11:48 AM

RE: Crosley 10-136 - by Radioroslyn - 04-09-2016, 12:13 PM

RE: Crosley 10-136 - by TV MAN - 04-18-2016, 07:35 AM

RE: Crosley 10-136 - by Eric - 04-18-2016, 05:50 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

Who's Online

There are currently 3595 online users. [Complete List]
» 1 Member(s) | 3594 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me