Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 89B won't oscillate!
#2

Don't de-solder the coil, bite it out as close to the pins as possible, then clean the lugs.
The wires should have a little slack to be able to solder them back when the coil is reinstalled.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Philco 89B won't oscillate! - by Steve McDonald - 04-13-2016, 01:00 PM
RE: Philco 89B won't oscillate! - by morzh - 04-13-2016, 04:03 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 04-13-2016, 05:31 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 04-13-2016, 06:34 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 04-13-2016, 07:48 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 04-13-2016, 08:00 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 04-13-2016, 09:34 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 04-13-2016, 10:43 PM
RE: Philco 89B won't oscillate! - by morzh - 04-14-2016, 02:13 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 04-14-2016, 07:10 PM
RE: Philco 89B won't oscillate! - by KCMike - 04-14-2016, 09:30 PM
RE: Philco 89B won't oscillate! - by klondike98 - 05-02-2016, 05:38 PM
RE: Philco 89B won't oscillate! - by klondike98 - 05-06-2016, 02:24 PM
RE: Philco 89B won't oscillate! - by klondike98 - 05-06-2016, 04:53 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 05-09-2016, 06:51 PM
RE: Philco 89B won't oscillate! - by KCMike - 05-10-2016, 01:13 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 05-10-2016, 01:34 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 07-11-2016, 06:57 AM
RE: Philco 89B won't oscillate! - by Radioroslyn - 07-11-2016, 06:09 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 07-11-2016, 08:28 PM
RE: Philco 89B won't oscillate! - by Radioroslyn - 07-12-2016, 07:18 AM
89B DOES Oscillate!! - by Steve McDonald - 05-02-2016, 04:03 PM
89B DOES Oscillate!! - by Steve McDonald - 05-06-2016, 02:09 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM

[-]
Who's Online
There are currently 2058 online users. [Complete List]
» 2 Member(s) | 2056 Guest(s)
AvatarAvatar

>