Philco consul model 144X

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco consul model 144X

flatheadjr
Member

Posts: 135
Threads: 14
Joined: Mar 2016
City: Idaho Falls, Idaho

#18

04-16-2016, 01:19 PM

My service data sheet says plate volts @ 300 and screen grid volts @ 310 no cathode voltage. If you go down the chart on the tube page depending on what that tube is being used for the voltage can go to 350. My schematic ohms out the field coil to 660 ohms, my meter read around 675 ohms I may have typed the wrong number before.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco consul model 144X - by flatheadjr - 04-15-2016, 12:01 AM

RE: Philco consul model 144X - by Arran - 04-15-2016, 12:25 AM

RE: Philco consul model 144X - by morzh - 04-15-2016, 08:04 AM

RE: Philco consul model 144X - by flatheadjr - 04-15-2016, 09:18 AM

RE: Philco consul model 144X - by morzh - 04-15-2016, 11:00 AM

RE: Philco consul model 144X - by flatheadjr - 04-15-2016, 12:18 PM

RE: Philco consul model 144X - by morzh - 04-15-2016, 05:01 PM

RE: Philco consul model 144X - by flatheadjr - 04-15-2016, 07:49 PM

RE: Philco consul model 144X - by morzh - 04-15-2016, 07:50 PM

RE: Philco consul model 144X - by flatheadjr - 04-15-2016, 08:56 PM

RE: Philco consul model 144X - by morzh - 04-15-2016, 09:07 PM

RE: Philco consul model 144X - by flatheadjr - 04-15-2016, 09:29 PM

RE: Philco consul model 144X - by Raleigh - 04-15-2016, 10:36 PM

RE: Philco consul model 144X - by flatheadjr - 04-16-2016, 01:43 AM

RE: Philco consul model 144X - by Raleigh - 04-16-2016, 09:47 AM

RE: Philco consul model 144X - by flatheadjr - 04-16-2016, 10:48 AM

RE: Philco consul model 144X - by Raleigh - 04-16-2016, 12:12 PM

RE: Philco consul model 144X - by flatheadjr - 04-16-2016, 01:19 PM

RE: Philco consul model 144X - by Radioroslyn - 04-16-2016, 03:12 PM

RE: Philco consul model 144X - by flatheadjr - 04-16-2016, 07:03 PM

RE: Philco consul model 144X - by Radioroslyn - 04-16-2016, 09:27 PM

RE: Philco consul model 144X - by flatheadjr - 04-18-2016, 11:15 PM

RE: Philco consul model 144X - by Radioroslyn - 04-18-2016, 11:43 PM

RE: Philco consul model 144X - by flatheadjr - 04-19-2016, 12:31 AM

RE: Philco consul model 144X - by flatheadjr - 04-19-2016, 03:09 PM

RE: Philco consul model 144X - by Radioroslyn - 04-20-2016, 04:30 PM

RE: Philco consul model 144X - by sam - 04-20-2016, 07:44 PM

RE: Philco consul model 144X - by klondike98 - 04-20-2016, 08:29 PM

RE: Philco consul model 144X - by flatheadjr - 04-21-2016, 12:04 AM

RE: Philco consul model 144X - by Radioroslyn - 04-21-2016, 07:02 AM

RE: Philco consul model 144X - by flatheadjr - 04-22-2016, 06:08 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
I have been playing the radio for a while now and doing well. Turned it on today and all I got was a whole lot of noise....dconant — 09:39 AM
Rusty Tuning Condenser
Thanks guys. I think I'll give the Naval Jelly a try since I can better control where it goes.dconant — 09:23 AM
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM

Who's Online

There are currently 3410 online users. [Complete List]
» 2 Member(s) | 3408 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me