1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Beam of Light Demo
Ampico-kid
Junior Member
**
Posts: 8
Threads: 3
Joined: May 2006
City: Harpers Ferry State, Province, Country: WV
#3

06-07-2009, 10:28 PM
Dave D Wrote:Ampico, That sounded great. That is the first beam of light that I have ever seen. Looks and sounds like you did a good job.

Dave D
Thanks Dave.....I guess there aren't too many of these BOL units around that are working. I feel very fortunate to have one of the few fully operational examples.

Bob
Find
« Next Oldest | Next Newest »


Messages In This Thread
Beam of Light Demo - by Ampico-kid - 06-05-2009, 07:49 PM
Re: Beam of Light Demo - by Dave D - 06-05-2009, 10:08 PM
Re: Beam of Light Demo - by Ampico-kid - 06-07-2009, 10:28 PM
Re: Beam of Light Demo - by Dave D - 06-07-2009, 11:22 PM
Re: Beam of Light Demo - by Music in a bottle - 06-08-2009, 12:11 PM
Re: Beam of Light Demo - by Chuck Schwark - 06-08-2009, 12:53 PM
Re: Beam of Light Demo - by Don Lind - 06-08-2009, 01:59 PM
Re: Beam of Light Demo - by Ampico-kid - 06-08-2009, 04:04 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently 1154 online users. [Complete List]
» 1 Member(s) | 1153 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration