1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Shadow Graph Problem
radiohenry
Senior Member
****
Posts: 496
Threads: 15
Joined: Mar 2013
City: Weymouth Ma
#7

04-24-2016, 09:29 AM
What about the sticky backed magnets used for crafts ?  You can cut it to fit and its not very thick.
                                              Henry
Find
« Next Oldest | Next Newest »


Messages In This Thread
Shadow Graph Problem - by joybird - 04-23-2016, 06:08 PM
RE: Shadow Graph Problem - by morzh - 04-23-2016, 06:26 PM
RE: Shadow Graph Problem - by joybird - 04-23-2016, 07:09 PM
RE: Shadow Graph Problem - by Eliot Ness - 04-23-2016, 07:21 PM
RE: Shadow Graph Problem - by morzh - 04-23-2016, 07:31 PM
RE: Shadow Graph Problem - by joybird - 04-23-2016, 08:02 PM
RE: Shadow Graph Problem - by radiohenry - 04-24-2016, 09:29 AM
RE: Shadow Graph Problem - by joybird - 04-24-2016, 10:32 AM
RE: Shadow Graph Problem - by morzh - 04-24-2016, 10:51 AM
RE: Shadow Graph Problem - by joybird - 04-24-2016, 11:25 AM
RE: Shadow Graph Problem - by Eliot Ness - 04-24-2016, 12:06 PM
RE: Shadow Graph Problem - by joybird - 04-24-2016, 01:52 PM
RE: Shadow Graph Problem - by joybird - 04-24-2016, 02:08 PM
RE: Shadow Graph Problem - by morzh - 04-24-2016, 03:01 PM
RE: Shadow Graph Problem - by Phlogiston - 05-02-2016, 02:15 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

[-]
Who's Online
There are currently 4045 online users. [Complete List]
» 2 Member(s) | 4043 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios