GE 115 troubleshooting

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

GE 115 troubleshooting

gregb
Senior Member

Posts: 599
Threads: 24
Joined: Jan 2014
City: Edmonton AB CA

#17

04-27-2016, 07:25 PM

Eric, I just noticed that the substitute loop you are using is very different from the original. That may be the whole problem right there, the original shows 25 ohms and the one you have in there shows as 2.5 ohms, a lot less windings.

Gregb

Find

« Next Oldest | Next Newest »

Messages In This Thread

GE 115 troubleshooting - by Eric - 04-22-2016, 04:27 PM

RE: GE 115 troubleshooting - by Eliot Ness - 04-22-2016, 05:35 PM

RE: GE 115 troubleshooting - by Eric - 04-22-2016, 06:51 PM

RE: GE 115 troubleshooting - by Arran - 04-23-2016, 03:20 AM

RE: GE 115 troubleshooting - by Eric - 04-23-2016, 09:25 AM

RE: GE 115 troubleshooting - by Radioroslyn - 04-23-2016, 11:19 AM

RE: GE 115 troubleshooting - by Eric - 04-23-2016, 01:51 PM

RE: GE 115 troubleshooting - by David - 04-23-2016, 08:25 PM

RE: GE 115 troubleshooting - by Eric - 04-23-2016, 08:59 PM

RE: GE 115 troubleshooting - by Joe Rossi - 04-24-2016, 10:17 AM

RE: GE 115 troubleshooting - by David - 04-25-2016, 08:38 PM

RE: GE 115 troubleshooting - by Eric - 04-26-2016, 02:40 PM

RE: GE 115 troubleshooting - by Radioroslyn - 04-26-2016, 03:27 PM

RE: GE 115 troubleshooting - by gregb - 04-26-2016, 03:34 PM

RE: GE 115 troubleshooting - by Eric - 04-27-2016, 04:31 PM

RE: GE 115 troubleshooting - by John R - 04-27-2016, 05:40 PM

RE: GE 115 troubleshooting - by gregb - 04-27-2016, 07:25 PM

RE: GE 115 troubleshooting - by Eric - 04-28-2016, 10:31 AM

RE: GE 115 troubleshooting - by Eric - 04-28-2016, 10:41 AM

RE: GE 115 troubleshooting - by Radioroslyn - 04-28-2016, 01:04 PM

RE: GE 115 troubleshooting - by Eric - 05-01-2016, 07:23 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me