GE 115 troubleshooting

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

GE 115 troubleshooting

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#20

04-28-2016, 01:04 PM

#1 Yes. Probably should use an isolation transformer connected to ac power powering the radio.
#2 Dc setting is used for any audio signal (from the volume all the way though to the spkr) Diode is for any rf /if signal (from ant loop though to the secondary of the second if transformer.
#3 B- is good.

Happy hunting!
Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

GE 115 troubleshooting - by Eric - 04-22-2016, 04:27 PM

RE: GE 115 troubleshooting - by Eliot Ness - 04-22-2016, 05:35 PM

RE: GE 115 troubleshooting - by Eric - 04-22-2016, 06:51 PM

RE: GE 115 troubleshooting - by Arran - 04-23-2016, 03:20 AM

RE: GE 115 troubleshooting - by Eric - 04-23-2016, 09:25 AM

RE: GE 115 troubleshooting - by Radioroslyn - 04-23-2016, 11:19 AM

RE: GE 115 troubleshooting - by Eric - 04-23-2016, 01:51 PM

RE: GE 115 troubleshooting - by David - 04-23-2016, 08:25 PM

RE: GE 115 troubleshooting - by Eric - 04-23-2016, 08:59 PM

RE: GE 115 troubleshooting - by Joe Rossi - 04-24-2016, 10:17 AM

RE: GE 115 troubleshooting - by David - 04-25-2016, 08:38 PM

RE: GE 115 troubleshooting - by Eric - 04-26-2016, 02:40 PM

RE: GE 115 troubleshooting - by Radioroslyn - 04-26-2016, 03:27 PM

RE: GE 115 troubleshooting - by gregb - 04-26-2016, 03:34 PM

RE: GE 115 troubleshooting - by Eric - 04-27-2016, 04:31 PM

RE: GE 115 troubleshooting - by John R - 04-27-2016, 05:40 PM

RE: GE 115 troubleshooting - by gregb - 04-27-2016, 07:25 PM

RE: GE 115 troubleshooting - by Eric - 04-28-2016, 10:31 AM

RE: GE 115 troubleshooting - by Eric - 04-28-2016, 10:41 AM

RE: GE 115 troubleshooting - by Radioroslyn - 04-28-2016, 01:04 PM

RE: GE 115 troubleshooting - by Eric - 05-01-2016, 07:23 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5486 online users. [Complete List]
» 2 Member(s) | 5484 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me