Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Big score!
#8

NICE SCORE!  I wish I could get that lucky just once. Nice find! Icon_clap Icon_clap Icon_thumbup Icon_thumbup


Messages In This Thread
Big score! - by sdradioman - 05-01-2016, 09:04 PM
RE: Big score! - by GarySP - 05-01-2016, 09:08 PM
RE: Big score! - by klondike98 - 05-01-2016, 09:12 PM
RE: Big score! - by KCMike - 05-01-2016, 09:47 PM
RE: Big score! - by VntgRads - 05-02-2016, 08:59 PM
RE: Big score! - by morzh - 05-02-2016, 10:49 PM
RE: Big score! - by palegreenthumb - 05-03-2016, 06:45 AM
RE: Big score! - by PhilcoJohn - 05-03-2016, 07:30 AM
RE: Big score! - by Eliot Ness - 05-03-2016, 07:52 AM
RE: Big score! - by Arran - 05-04-2016, 02:52 AM
RE: Big score! - by OldRestorer - 05-04-2016, 02:32 PM
RE: Big score! - by Joe Rossi - 05-04-2016, 08:12 PM
RE: Big score! - by Radioroslyn - 05-04-2016, 08:20 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

[-]
Who's Online
There are currently 4029 online users. [Complete List]
» 2 Member(s) | 4027 Guest(s)
AvatarAvatar

>