Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA Q-103 tube ?
#1

I have this RCA  Q-103, http://www.nostalgiaair.org/pagesbymodel...015596.pdf  The correct schematic is the one on top for the Q103

And I have a question on the alignment page 16-11 the chart on the right hand side for the Q-103.
#1 12SK7 IF grid?  Do they mean pin 2,4 or pin 6? I think 6?
#2 12SA7 1st Dect grid. Do they mean 1,4,5 or pin 8? I think 4?

Thanks Eric


Messages In This Thread
RCA Q-103 tube ? - by Eric - 05-06-2016, 03:00 PM
RE: RCA Q-103 tube ? - by Phlogiston - 05-06-2016, 03:35 PM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-07-2016, 12:12 AM
RE: RCA Q-103 tube ? - by Eric - 05-08-2016, 09:42 AM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-08-2016, 07:34 PM
RE: RCA Q-103 tube ? - by Eric - 05-11-2016, 03:35 PM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-11-2016, 04:32 PM
RE: RCA Q-103 tube ? - by Eric - 05-12-2016, 03:20 PM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-12-2016, 03:57 PM
RE: RCA Q-103 tube ? - by Eric - 05-13-2016, 08:58 AM
RE: RCA Q-103 tube ? - by Eric - 05-17-2016, 11:02 AM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-17-2016, 04:33 PM
RE: RCA Q-103 tube ? - by Eric - 05-19-2016, 04:51 PM
RE: RCA Q-103 tube ? - by Eric - 05-18-2016, 07:19 PM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-18-2016, 07:54 PM
RE: RCA Q-103 tube ? - by Eric - 05-19-2016, 10:45 AM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-19-2016, 06:16 PM
RE: RCA Q-103 tube ? - by Eric - 05-20-2016, 11:55 AM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-20-2016, 09:16 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>