1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Sears silvertone question
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#9

05-09-2016, 08:06 PM
< 307 volts DC schem. calls for 375V
Could have a weak 5U4. See it in tv's a lot.
If you measure from p4 to p6 on the 5U4 should see about 800vac.

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
Sears silvertone question - by KCMike - 05-07-2016, 02:33 PM
RE: Sears silvertone question - by Phlogiston - 05-07-2016, 02:41 PM
RE: Sears silvertone question - by KCMike - 05-07-2016, 03:44 PM
RE: Sears silvertone question - by Phlogiston - 05-07-2016, 05:59 PM
RE: Sears silvertone question - by morzh - 05-07-2016, 03:47 PM
RE: Sears silvertone question - by KCMike - 05-07-2016, 03:59 PM
RE: Sears silvertone question - by KCMike - 05-07-2016, 06:23 PM
RE: Sears silvertone question - by KCMike - 05-09-2016, 12:44 PM
RE: Sears silvertone question - by Radioroslyn - 05-09-2016, 08:06 PM
RE: Sears silvertone question - by KCMike - 05-09-2016, 08:18 PM
RE: Sears silvertone question - by KCMike - 11-15-2016, 12:04 PM
RE: Sears silvertone question - by sam - 11-15-2016, 08:07 PM
RE: Sears silvertone question - by KCMike - 11-15-2016, 09:22 PM
RE: Sears silvertone question - by Phlogiston - 11-17-2016, 11:29 AM
RE: Sears silvertone question - by Radiola214 - 06-18-2019, 02:19 PM
RE: Sears silvertone question - by KCMike - 06-18-2019, 08:51 PM
RE: Sears silvertone question - by Radiola214 - 06-19-2019, 05:34 AM
RE: Sears silvertone question - by KCMike - 06-19-2019, 12:03 PM
RE: Sears silvertone question - by KCMike - 06-19-2019, 05:06 PM
RE: Sears silvertone question - by Radiola214 - 06-20-2019, 12:43 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4741 online users. [Complete List]
» 2 Member(s) | 4739 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)