cleaning philco dials

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

cleaning philco dials

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

05-10-2016, 09:06 AM

One note: When you use mineral spirits, do not rub the lettering hard, else it will start to remove the lettering...a light touch is best.

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Messages In This Thread

cleaning philco dials - by vaguy22 - 05-09-2016, 10:28 PM

RE: cleaning philco dials - by Radioroslyn - 05-09-2016, 11:59 PM

RE: cleaning philco dials - by Radioroslyn - 05-10-2016, 07:33 AM

RE: cleaning philco dials - by sam - 05-10-2016, 12:23 AM

RE: cleaning philco dials - by kiwi_steve - 05-10-2016, 06:39 AM

RE: cleaning philco dials - by morzh - 05-10-2016, 07:47 AM

RE: cleaning philco dials - by vaguy22 - 05-10-2016, 08:56 AM

RE: cleaning philco dials - by Ron Ramirez - 05-10-2016, 09:06 AM

RE: cleaning philco dials - by vaguy22 - 05-10-2016, 10:00 AM

RE: cleaning philco dials - by HOTWIRE - 05-13-2016, 07:16 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM

Who's Online

There are currently 4851 online users. [Complete List]
» 3 Member(s) | 4848 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me