Thread Rating:
  • 1 Vote(s) - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA RC-350
#2

Nice find!!! It's a little 4 tube trf set. http://www.nostalgiaair.org/pagesbymodel...015390.pdf Too bad it's a curtain burner.
You may want to consider changing the tubes, 6K7 for a 12K7, 6j7 for a 12J7, 25Z6 to a 50Y6 and the 25L6 to a 50L6. These would be drop in replacement no rewiring the sockets and the pilot lamp will work if you remove the resistor across it. This way you won't need a resistance line cord or a line dropping capacitor. On these small sets it can be a problem finding space for a large cap.

Terry


Messages In This Thread
RCA RC-350 - by Jayce - 05-11-2016, 03:13 PM
RE: RCA RC-350 - by Radioroslyn - 05-11-2016, 04:34 PM
RE: RCA RC-350 - by KCMike - 05-11-2016, 05:12 PM
RE: RCA RC-350 - by Paul Philco322 - 05-11-2016, 05:26 PM
RE: RCA RC-350 - by morzh - 05-11-2016, 10:04 PM
RE: RCA RC-350 - by JimZ - 05-12-2016, 07:23 AM
RE: RCA RC-350 - by Arran - 05-13-2016, 12:53 AM
RE: RCA RC-350 - by Jayce - 05-12-2016, 04:43 PM
RE: RCA RC-350 - by JimZ - 05-13-2016, 08:08 AM
RE: RCA RC-350 - by Jayce - 05-13-2016, 08:25 PM
RE: RCA RC-350 - by JimZ - 05-14-2016, 02:49 PM
RE: RCA RC-350 - by Arran - 05-16-2016, 02:46 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>