Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Philco 97 - RF problem... HELP!
#25

> hakkas
??

I'm a bit of a primitive guy so I would connect an outdoor antenna to the Philco and loose couple the output of the RF amp (grid cap of the 6A7) to the antenna post of a BC set. This can be accomplished by a  a small cap (100pf or so or 2 pieces of hookup wire twisted together a bunch of times). Tune both sets to a station on the same frequency and see if the station as you tune the Philco.
By connecting the generator and scope to the coil it may detune it from added capacity from each device.

Terry


Messages In This Thread
Philco 97 - RF problem... HELP! - by kiwi_steve - 05-01-2016, 09:38 PM
RE: Philco 97 - by KCMike - 05-01-2016, 09:53 PM
RE: Philco 97 - by kiwi_steve - 05-01-2016, 11:59 PM
RE: Philco 97 - by kiwi_steve - 05-02-2016, 03:02 AM
RE: Philco 97 - by kiwi_steve - 05-02-2016, 03:18 AM
RE: Philco 97 - by kiwi_steve - 05-02-2016, 11:50 PM
RE: Philco 97 - by kiwi_steve - 05-03-2016, 02:41 AM
RE: Philco 97 - by kiwi_steve - 05-07-2016, 08:27 PM
RE: Philco 97 - by Mondial - 05-08-2016, 10:25 AM
RE: Philco 97 - by HOTWIRE - 05-08-2016, 11:44 AM
RE: Philco 97 - by kiwi_steve - 05-08-2016, 12:27 PM
RE: Philco 97 - by HOTWIRE - 05-09-2016, 09:55 AM
RE: Philco 97 - by kiwi_steve - 05-09-2016, 03:55 PM
RE: Philco 97 - by HOTWIRE - 05-09-2016, 12:44 PM
RE: Philco 97 - by HOTWIRE - 05-09-2016, 05:01 PM
RE: Philco 97 - by HOTWIRE - 05-09-2016, 05:28 PM
RE: Philco 97 - by kiwi_steve - 05-09-2016, 05:49 PM
RE: Philco 97 - by kiwi_steve - 05-09-2016, 05:31 PM
RE: Philco 97 - by HOTWIRE - 05-09-2016, 07:51 PM
RE: Philco 97 - by kiwi_steve - 05-09-2016, 08:31 PM
RE: Philco 97 - by kiwi_steve - 05-10-2016, 01:32 AM
RE: Philco 97 - by HOTWIRE - 05-10-2016, 05:28 AM
RE: Philco 97 - by kiwi_steve - 05-10-2016, 06:33 AM
RE: Philco 97 - RF problem... HELP! - by Radioroslyn - 05-11-2016, 08:16 PM
RE: Philco 97 - RF problem... HELP! - by HOTWIRE - 05-12-2016, 05:20 AM
RE: Philco 97 - RF problem... HELP! - by morzh - 05-12-2016, 07:34 AM
RE: Philco 97 - RF problem... HELP! - by HOTWIRE - 05-12-2016, 08:58 AM
RE: Philco 97 - RF problem... HELP! - by Mondial - 05-15-2016, 03:18 PM
RE: Philco 97 - RF problem... HELP! - by Mondial - 05-15-2016, 07:21 PM
RE: Philco 97 - RF problem... HELP! - by HOTWIRE - 06-20-2016, 09:38 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM
54C Complete Teardown/Rebuild
Richard, Had grabbed it already but thank you just the same.  I find myself wanting to find some way to block out the...glyphmon — 12:03 AM
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting.  IF alignment went great, almost all was already spot-on.  Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project.  O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today.  Soldered one in and had a successful first power-up.  No magic smoke escaped and it tunes in...glyphmon — 09:53 PM

[-]
Who's Online
There are currently no members online.

>