Where does

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Where does

sam
Phorum Expert

Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj

05-16-2016, 11:16 AM

if I known you liked it I would had fit it in their Icon_thumbup

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2

Find

« Next Oldest | Next Newest »

Messages In This Thread

Where does - by Radioroslyn - 05-15-2016, 01:14 PM

RE: Where does - by sam - 05-15-2016, 01:58 PM

RE: Where does - by morzh - 05-15-2016, 02:06 PM

RE: Where does - by gregb - 05-15-2016, 02:36 PM

RE: Where does - by Radioroslyn - 05-15-2016, 02:53 PM

RE: Where does - by OldRestorer - 05-15-2016, 07:36 PM

RE: Where does - by Ron Ramirez - 05-16-2016, 09:08 AM

RE: Where does - by Radioroslyn - 05-16-2016, 12:09 PM

RE: Where does - by Ron Ramirez - 05-16-2016, 09:48 PM

RE: Where does - by sam - 05-16-2016, 11:16 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

Who's Online

There are currently 4574 online users. [Complete List]
» 3 Member(s) | 4571 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me