Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-61 Issues
#11

Did not realize the 6F6 was out of the socket, then the voltage is good.

Dumb question: is your speaker good?

I dealt with just that recently - 4 weeks ago I tested the radio with no sound.....turned out one of the voice coil leads was not there so the output transformer was not driving anything. But if you test across the output you will see the continuity of the secondary coil.

See if you can unsolder one output lead of the transformer and measure across the voice coil.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
37-61 Issues - by Tgace459 - 05-18-2016, 07:53 AM
RE: 37-61 Issues - by KCMike - 05-18-2016, 08:47 AM
RE: 37-61 Issues - by Steve Davis - 05-18-2016, 08:47 AM
RE: 37-61 Issues - by Eliot Ness - 05-18-2016, 08:59 AM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 09:14 AM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 09:18 AM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 10:43 AM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 12:09 PM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 01:22 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 01:25 PM
RE: 37-61 Issues - by morzh - 05-18-2016, 01:34 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 01:45 PM
RE: 37-61 Issues - by morzh - 05-18-2016, 01:47 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 01:55 PM
RE: 37-61 Issues - by KCMike - 05-18-2016, 02:12 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 02:13 PM
RE: 37-61 Issues - by morzh - 05-18-2016, 02:23 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 02:30 PM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 03:16 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 04:30 PM
RE: 37-61 Issues - by morzh - 05-18-2016, 04:42 PM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 04:44 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 04:48 PM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 05:35 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 07:29 PM
RE: 37-61 Issues - by morzh - 05-18-2016, 07:40 PM
RE: 37-61 Issues - by Steve Davis - 05-18-2016, 10:58 PM
RE: 37-61 Issues - by Tgace459 - 05-19-2016, 07:22 AM
RE: 37-61 Issues - by Radioroslyn - 05-19-2016, 07:57 AM
RE: 37-61 Issues - by morzh - 05-19-2016, 08:33 AM
RE: 37-61 Issues - by Tgace459 - 05-20-2016, 11:01 AM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4858 online users. [Complete List]
» 2 Member(s) | 4856 Guest(s)
AvatarAvatar

>