Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-61 Issues
#16

Well. Im thinking its either the 6f6g tube or the pins....I wigggled the tube from the top and it came back on but as I tried to adjust the tuner (specifically when I went all the way over to the low end of the dial) "pop" it died again.

Interesting enough the 3 pin is the one I had to soldier a couple of wires too and the solder job isn't spectacular. Maybe a cold joint?


Messages In This Thread
37-61 Issues - by Tgace459 - 05-18-2016, 07:53 AM
RE: 37-61 Issues - by KCMike - 05-18-2016, 08:47 AM
RE: 37-61 Issues - by Steve Davis - 05-18-2016, 08:47 AM
RE: 37-61 Issues - by Eliot Ness - 05-18-2016, 08:59 AM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 09:14 AM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 09:18 AM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 10:43 AM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 12:09 PM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 01:22 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 01:25 PM
RE: 37-61 Issues - by morzh - 05-18-2016, 01:34 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 01:45 PM
RE: 37-61 Issues - by morzh - 05-18-2016, 01:47 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 01:55 PM
RE: 37-61 Issues - by KCMike - 05-18-2016, 02:12 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 02:13 PM
RE: 37-61 Issues - by morzh - 05-18-2016, 02:23 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 02:30 PM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 03:16 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 04:30 PM
RE: 37-61 Issues - by morzh - 05-18-2016, 04:42 PM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 04:44 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 04:48 PM
RE: 37-61 Issues - by Radioroslyn - 05-18-2016, 05:35 PM
RE: 37-61 Issues - by Tgace459 - 05-18-2016, 07:29 PM
RE: 37-61 Issues - by morzh - 05-18-2016, 07:40 PM
RE: 37-61 Issues - by Steve Davis - 05-18-2016, 10:58 PM
RE: 37-61 Issues - by Tgace459 - 05-19-2016, 07:22 AM
RE: 37-61 Issues - by Radioroslyn - 05-19-2016, 07:57 AM
RE: 37-61 Issues - by morzh - 05-19-2016, 08:33 AM
RE: 37-61 Issues - by Tgace459 - 05-20-2016, 11:01 AM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A5...MrFixr55 — 06:48 AM

[-]
Who's Online
There are currently 5195 online users. [Complete List]
» 4 Member(s) | 5191 Guest(s)
AvatarAvatarAvatarAvatar

>