1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco 60 dial slipping
morzh
Odobenus rosmarus
*****
Posts: 15,822
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#2

05-19-2016, 04:22 PM
Is this the one with a bell-shaped cover going over balls pressing the shaft to the cap, bolted with two screws?

You need to clean under the bell, it works on the friction. Or simply tighten it first, see if it works.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 05-19-2016, 04:23 PM by morzh.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
philco 60 dial slipping - by vaguy22 - 05-19-2016, 04:09 PM
RE: philco 60 dial slipping - by morzh - 05-19-2016, 04:22 PM
RE: philco 60 dial slipping - by klondike98 - 05-19-2016, 04:30 PM
RE: philco 60 dial slipping - by Radioroslyn - 05-19-2016, 05:26 PM
RE: philco 60 dial slipping - by klondike98 - 05-19-2016, 08:10 PM
RE: philco 60 dial slipping - by morzh - 05-19-2016, 08:17 PM
RE: philco 60 dial slipping - by vaguy22 - 05-19-2016, 11:00 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4861 online users. [Complete List]
» 4 Member(s) | 4857 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration