Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA Q-103 tube ?
#18

(05-19-2016, 06:16 PM)Radioroslyn Wrote:  Good! Now we know that the oscillator is working and is working at the proper tuning range. This will assure that the stations received will be on there proper places on the dial.
Part 2
With your antenna connected tune in a local station near 600kc then adjust L2 for loudest signal from the spkr. Find a local station near 1300kc and C1 for loudest from the spkr.

Just for grins tune your generator to 455kc. Connect the output to the antenna post of your Hammerlund and listen for it's signal @ 910kc (that would be the generator's 2nd harmonic 455x2=910) to see if your generator is on frequency @455kc. If your not hearing a signal at 910kc then retune the generator till you do then re adjust the IF transformers in your RCA noting that all of the adjusts (4) do make some difference when adjusted. If not there is a problem with the IF transformer.

Just to be clear your set doesn't have a built in loop ant it does require an external ant to hear much of anything. With that being said it should be able to pick stations with 10-15' of wire hooked up to it. I would think that WSB should knock your sock off as I can get it up here near Phila.

Sorry we have to have done this sort of basacwards but I want to be sure there wasn't a problem with the osc. It's doing it's thing! This set going to make you a pro at fixin'

Terry
Everything came in great, picked up the 910 on the Hammerlund as close to perfect as you can get on the scale of the signal gen for 455. I think this RCA set is very sensitive and the adjustments are very touchy compound this by my not having a long enough antenna at the start of this (about 8-12") right now I have a 6' wire attached which I attache my garage ant about 20. Since the instruction doesn't give a length for the antenna what would be good 10'?
Thanks for the help!
Eric


Messages In This Thread
RCA Q-103 tube ? - by Eric - 05-06-2016, 03:00 PM
RE: RCA Q-103 tube ? - by Phlogiston - 05-06-2016, 03:35 PM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-07-2016, 12:12 AM
RE: RCA Q-103 tube ? - by Eric - 05-08-2016, 09:42 AM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-08-2016, 07:34 PM
RE: RCA Q-103 tube ? - by Eric - 05-11-2016, 03:35 PM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-11-2016, 04:32 PM
RE: RCA Q-103 tube ? - by Eric - 05-12-2016, 03:20 PM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-12-2016, 03:57 PM
RE: RCA Q-103 tube ? - by Eric - 05-13-2016, 08:58 AM
RE: RCA Q-103 tube ? - by Eric - 05-17-2016, 11:02 AM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-17-2016, 04:33 PM
RE: RCA Q-103 tube ? - by Eric - 05-19-2016, 04:51 PM
RE: RCA Q-103 tube ? - by Eric - 05-18-2016, 07:19 PM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-18-2016, 07:54 PM
RE: RCA Q-103 tube ? - by Eric - 05-19-2016, 10:45 AM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-19-2016, 06:16 PM
RE: RCA Q-103 tube ? - by Eric - 05-20-2016, 11:55 AM
RE: RCA Q-103 tube ? - by Radioroslyn - 05-20-2016, 09:16 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5575 online users. [Complete List]
» 1 Member(s) | 5574 Guest(s)
Avatar

>