Hum after recap (40-160)

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Hum after recap (40-160)

Stan the Man
Member

Posts: 62
Threads: 10
Joined: Nov 2015
City: Memphis,Tn

05-20-2016, 01:05 PM

Terry , yes I have nothing but the hum.. I'm holding on to the hope its a bad tube.. I hate to buy a set of tubes just because I don't have a way to test what I have,.. Voltage check, YES!! Thank you,.. I will voltage check before I buy tubes..

Thanks, Stan

(This post was last modified: 05-20-2016, 01:10 PM by Stan the Man.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Hum after recap (40-160) - by Stan the Man - 05-20-2016, 11:39 AM

RE: Hum after recap (40-160) - by Radioroslyn - 05-20-2016, 12:06 PM

RE: Hum after recap (40-160) - by Radioroslyn - 05-20-2016, 12:18 PM

RE: Hum after recap (40-160) - by Stan the Man - 05-20-2016, 01:05 PM

RE: Hum after recap (40-160) - by Radioroslyn - 05-20-2016, 01:28 PM

RE: Hum after recap (40-160) - by Stan the Man - 05-20-2016, 06:07 PM

RE: Hum after recap (40-160) - by Stan the Man - 05-22-2016, 08:14 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM

Who's Online

There are currently 2945 online users. [Complete List]
» 3 Member(s) | 2942 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me