1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
16B cathedral side switch
Eliot Ness
Phorum Expert
*****
Posts: 3,135
Threads: 54
Joined: Apr 2011
City: Lexington, KY
#9

05-22-2016, 01:48 PM
I didn't realize what you meant when you said "frame", but if the hole is on the inside and not the outside it's time to do a little drilling.  
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Find
« Next Oldest | Next Newest »


Messages In This Thread
16B cathedral side switch - by morzh - 05-21-2016, 09:42 AM
RE: 16B cathedral side switch - by Steve Davis - 05-21-2016, 11:36 PM
RE: 16B cathedral side switch - by morzh - 05-22-2016, 10:08 AM
RE: 16B cathedral side switch - by Steve Davis - 05-22-2016, 10:12 AM
RE: 16B cathedral side switch - by Ron Ramirez - 05-22-2016, 10:17 AM
RE: 16B cathedral side switch - by morzh - 05-22-2016, 10:29 AM
RE: 16B cathedral side switch - by Eliot Ness - 05-22-2016, 11:54 AM
RE: 16B cathedral side switch - by morzh - 05-22-2016, 01:24 PM
RE: 16B cathedral side switch - by Eliot Ness - 05-22-2016, 01:48 PM
RE: 16B cathedral side switch - by KCMike - 05-22-2016, 02:04 PM
RE: 16B cathedral side switch - by morzh - 05-22-2016, 02:25 PM
RE: 16B cathedral side switch - by morzh - 05-22-2016, 07:46 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

[-]
Who's Online
There are currently 4380 online users. [Complete List]
» 2 Member(s) | 4378 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios