1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 1 Vote(s) - 1 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco 37-630 console cap value
quartermilecamel
Junior Member
**
Posts: 30
Threads: 4
Joined: May 2016
City: east canton, ohio
#12

05-24-2016, 03:42 AM
Yes I saw the tip about the hidden caps, but didnt know if there were any more hidden in there.  Also have seen this long 14 guage wire tip.  Although IM not sure if they are just taking solid house wire and installing that in their soldering iron or ordering special long tips.
 One amazing thing about the paper caps is they are all oriented so that you can only see the philco part number, yet every one of them does have the actual value, which is conveniently facing the chassis so you cant see it.  David grimes must have also come up with this idea.

I remember checking all the tubes, one was open, a 6k7(replaced with borrowed tube from another radio).  All show in the green area on a tripplett emissions tester.
(This post was last modified: 05-24-2016, 03:45 AM by quartermilecamel.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
RE: philco 37-630 console cap value - by morzh - 05-23-2016, 08:15 AM
RE: philco 37-630 console cap value - by morzh - 05-23-2016, 08:44 AM
RE: philco 37-630 console cap value - by KCMike - 05-23-2016, 09:03 AM
RE: philco 37-630 console cap value - by morzh - 05-23-2016, 09:17 AM
RE: philco 37-630 console cap value - by morzh - 05-23-2016, 09:24 AM
RE: philco 37-630 console cap value - by morzh - 05-23-2016, 04:42 PM
RE: philco 37-630 console cap value - by quartermilecamel - 05-24-2016, 03:42 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration