Philco95 Condenser Box

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco95 Condenser Box

PAradiogeek
Senior Member

Posts: 395
Threads: 33
Joined: Jul 2013
City: Horsham, PA

05-26-2016, 10:38 PM

OK, thanks for the tips guys. I got it all out. Those two 2 uF caps were HUGE!!

Tomorrow I'll put the new caps in place.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco95 Condenser Box - by PAradiogeek - 05-26-2016, 07:03 PM

RE: Philco95 Condenser Box - by morzh - 05-26-2016, 07:18 PM

RE: Philco95 Condenser Box - by Radioroslyn - 05-26-2016, 07:54 PM

RE: Philco95 Condenser Box - by PAradiogeek - 05-26-2016, 07:57 PM

RE: Philco95 Condenser Box - by morzh - 05-26-2016, 08:12 PM

RE: Philco95 Condenser Box - by PAradiogeek - 05-26-2016, 10:38 PM

RE: Philco95 Condenser Box - by PAradiogeek - 05-30-2016, 10:17 AM

RE: Philco95 Condenser Box - by PAradiogeek - 06-08-2016, 04:10 PM

RE: Philco95 Condenser Box - by Radioroslyn - 06-08-2016, 05:47 PM

RE: Philco95 Condenser Box - by PAradiogeek - 06-08-2016, 06:26 PM

RE: Philco95 Condenser Box - by Radioroslyn - 06-08-2016, 08:31 PM

RE: Philco95 Condenser Box - by PAradiogeek - 06-08-2016, 11:07 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

Who's Online

There are currently 4467 online users. [Complete List]
» 2 Member(s) | 4465 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me