41-290 Help

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

41-290 Help

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#10

05-27-2016, 09:13 AM

Plate load for the 41's is 12,000 ohms end to end or 6,000 ohms each side of center tap. This what you need to know to find a proper replacement. Load resistance and dc resistance are two different things. DC resistance is going to be a few hundred ohms.

GLOM
Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

41-290 Help - by KC2YSR - 04-01-2016, 08:13 AM

RE: 41-290 Help - by klondike98 - 04-01-2016, 11:28 AM

RE: 41-290 Help - by KC2YSR - 04-01-2016, 11:36 AM

RE: 41-290 Help - by KCMike - 04-01-2016, 11:53 AM

RE: 41-290 Help - by KC2YSR - 05-27-2016, 08:36 AM

RE: 41-290 Help - by morzh - 05-27-2016, 08:54 AM

RE: 41-290 Help - by KC2YSR - 05-27-2016, 08:57 AM

RE: 41-290 Help - by Radioroslyn - 05-27-2016, 08:57 AM

RE: 41-290 Help - by morzh - 05-27-2016, 09:03 AM

RE: 41-290 Help - by Radioroslyn - 05-27-2016, 09:13 AM

RE: 41-290 Help - by KC2YSR - 05-27-2016, 09:29 AM

RE: 41-290 Help - by morzh - 05-27-2016, 09:44 AM

RE: 41-290 Help - by KC2YSR - 05-27-2016, 10:07 AM

RE: 41-290 Help - by Radioroslyn - 05-27-2016, 10:30 AM

RE: 41-290 Help - by morzh - 05-27-2016, 11:08 AM

RE: 41-290 Help - by PAradiogeek - 05-27-2016, 11:22 AM

RE: 41-290 Help - by morzh - 05-27-2016, 11:38 AM

RE: 41-290 Help - by Radioroslyn - 05-27-2016, 11:39 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

Who's Online

There are currently 4646 online users. [Complete List]
» 4 Member(s) | 4642 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me