Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New member
#1

Hello!

My name is Juan and i am from Spain.
And new to the forum.

I have some valve radios and two of them are Phico, a 54C and a 84B.
I want to tell you that your threads has been very usefull to me
because the two Philcos are repaired and working after replacing resistors, capacitors,
new tubes, two coils rewounded ...,   perhaps they need a little touch yet, but not too much.

Thank you Icon_biggrin

Pd. I do apologise about my english, i haven’t wrote in english since twenty years ago and I don’t use on line translators.


Messages In This Thread
New member - by JRomero - 05-31-2016, 04:49 PM
RE: New member - by Steve Davis - 05-31-2016, 07:18 PM
RE: New member - by klondike98 - 05-31-2016, 07:25 PM
RE: New member - by OldRestorer - 05-31-2016, 07:29 PM
RE: New member - by morzh - 05-31-2016, 07:30 PM
RE: New member - by Eliot Ness - 05-31-2016, 09:27 PM
RE: New member - by PhilcoJohn - 06-01-2016, 06:55 AM
RE: New member - by Joe Rossi - 06-01-2016, 07:24 PM
RE: New member - by Radioroslyn - 06-01-2016, 07:25 PM
RE: New member - by JRomero - 06-03-2016, 06:05 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 5428 online users. [Complete List]
» 3 Member(s) | 5425 Guest(s)
AvatarAvatarAvatar

>