New member

Thread Rating:

New member

morzh
Odobenus rosmarus

Posts: 15,823
Threads: 554
Joined: Oct 2011
City: Jackson, NJ

05-31-2016, 07:30 PM

Bienvenido Juan!

Para un muchacho que no se han Ingles utilizado en 20 años, el suyo es seguro que muy bueno. Icon_lol

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.

(This post was last modified: 05-31-2016, 09:47 PM by morzh.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

New member - by JRomero - 05-31-2016, 04:49 PM

RE: New member - by Steve Davis - 05-31-2016, 07:18 PM

RE: New member - by klondike98 - 05-31-2016, 07:25 PM

RE: New member - by OldRestorer - 05-31-2016, 07:29 PM

RE: New member - by morzh - 05-31-2016, 07:30 PM

RE: New member - by Eliot Ness - 05-31-2016, 09:27 PM

RE: New member - by PhilcoJohn - 06-01-2016, 06:55 AM

RE: New member - by Joe Rossi - 06-01-2016, 07:24 PM

RE: New member - by Radioroslyn - 06-01-2016, 07:25 PM

RE: New member - by JRomero - 06-03-2016, 06:05 PM

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

Who's Online

There are currently 3757 online users. [Complete List]
» 1 Member(s) | 3756 Guest(s)