1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Zenith 7-S-240 Eye tube question
Eric
Senior Member
****
Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA
#7

06-01-2016, 02:41 PM
    Rechecked the following Resistors
R6 1.1megs  (1meg)
R7 442k   (330k) replaced now 330k
R8  216k   (220k)
R9  494k   (470k)
Replaced the tubes one at a time no difference.
Attached is the voltage check 6f6 pin 5 stands out unless misprint and Pin2 of the 6e5
Find
« Next Oldest | Next Newest »


Messages In This Thread
Zenith 7-S-240 Eye tube question - by Eric - 05-30-2016, 04:37 PM
RE: Zenith 7-S-240 Eye tube question - by morzh - 05-30-2016, 09:34 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 05-31-2016, 02:00 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-01-2016, 02:41 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-02-2016, 09:04 AM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-02-2016, 05:20 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-03-2016, 07:02 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-04-2016, 02:21 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-05-2016, 12:13 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-05-2016, 04:14 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-06-2016, 04:55 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-07-2016, 05:28 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-07-2016, 05:29 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-07-2016, 08:10 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-08-2016, 05:02 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6024 online users. [Complete List]
» 2 Member(s) | 6022 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)