Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith 7-S-240 Eye tube question
#18

Traced out all 6 pins and they go where they are supposed to.
also re-verified Resistors 5, 6, 7, 14, 15 and C7

Radio receives stations good (what I'm used to) have about 15-20' of antenna Vol is good across the stations
Ran all my eye tubes through the tube tester Knight 600A all were good also did the 6T5 again and it is better than I remembered so I'm going to use it

Hooked up a 9v with the + to chassis and the - to the 3 pin of the 6T5 it closes the eye about 15% from full open and drops the station vol by 30% also voltage goes from -2.8 to -9.2v with the battery

going to do some more tracing and verifying on what I have done

Nothing else to do on a rainy day down here!....:-)


Messages In This Thread
Zenith 7-S-240 Eye tube question - by Eric - 05-30-2016, 04:37 PM
RE: Zenith 7-S-240 Eye tube question - by morzh - 05-30-2016, 09:34 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 05-31-2016, 02:00 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-01-2016, 02:41 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-02-2016, 09:04 AM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-02-2016, 05:20 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-03-2016, 07:02 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-04-2016, 02:21 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-05-2016, 12:13 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-05-2016, 04:14 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-06-2016, 04:55 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-07-2016, 05:28 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-07-2016, 05:29 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-07-2016, 08:10 PM
RE: Zenith 7-S-240 Eye tube question - by Eric - 06-08-2016, 05:02 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>