1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco 87 chassis operational????
alwayslearning
Junior Member
**
Posts: 3
Threads: 1
Joined: Jun 2016
City: osceola, wi
#5

06-08-2016, 01:13 PM
Thanks Terry for your response.
I've already rebuilt the condenser can with 630v film capacitors - is that ok instead of mylar?
Check that 31 has been replaced...  If you're referring to the 0.015uF cap on the power input - yes it's been replaced with a film capacitor.  Should I just remove it as commented on by morzh?
3.  I know what oscillation means but maybe not in relation to AM receivers - can you elaborate?
Thanks,
Keith
Find
« Next Oldest | Next Newest »


Messages In This Thread
RE: philco 87 chassis operational???? - by alwayslearning - 06-08-2016, 01:13 PM
RE: philco 87 chassis operational???? - by morzh - 06-08-2016, 08:38 AM
RE: philco 87 chassis operational???? - by Arran - 06-11-2016, 05:04 AM
RE: philco 87 chassis operational???? - by morzh - 06-08-2016, 02:47 PM
RE: philco 87 chassis operational???? - by morzh - 06-11-2016, 12:10 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM

[-]
Who's Online
There are currently 2980 online users. [Complete List]
» 1 Member(s) | 2979 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration