GE 107 wont start up

Thread Rating:

1 Vote(s) - 2 Average
1
2
3
4
5

Linear Mode

GE 107 wont start up

klondike98
Phorum Moderator

Posts: 5,084
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR

#13

06-11-2016, 11:56 AM

re: pilot light. If any of the filaments in the tubes are open then the pilot light will not work. The filaments are all in series. Filaments are easy to check. Pull the tube and check the appropriate pins with your ohm meter for continuity. If all filaments are good then you may have a bad connection in the tube sockets (clean with Deoxit and use a fine sand paper or a nail file on the pins on the tubes). If it still doesn't work, check any solder connection that are in that circuit. After that...I'm out'a ideas.

Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

GE 107 wont start up - by Tgace459 - 06-09-2016, 08:43 PM

RE: GE 107 wont start up - by KCMike - 06-09-2016, 09:00 PM

RE: GE 107 wont start up - by morzh - 06-09-2016, 10:07 PM

RE: GE 107 wont start up - by Tgace459 - 06-10-2016, 12:15 AM

RE: GE 107 wont start up - by Arran - 06-10-2016, 12:22 AM

RE: GE 107 wont start up - by Tgace459 - 06-11-2016, 02:48 PM

RE: GE 107 wont start up - by Tgace459 - 06-11-2016, 03:13 PM

RE: GE 107 wont start up - by Tgace459 - 06-10-2016, 01:11 PM

RE: GE 107 wont start up - by leftwing25 - 06-10-2016, 05:28 PM

RE: GE 107 wont start up - by klondike98 - 06-10-2016, 05:40 PM

RE: GE 107 wont start up - by Tgace459 - 06-10-2016, 10:54 PM

RE: GE 107 wont start up - by gregb - 06-10-2016, 11:32 PM

RE: GE 107 wont start up - by Arran - 06-11-2016, 05:28 AM

RE: GE 107 wont start up - by Tgace459 - 06-11-2016, 11:29 AM

RE: GE 107 wont start up - by klondike98 - 06-11-2016, 11:56 AM

RE: GE 107 wont start up - by Tgace459 - 06-11-2016, 12:05 PM

RE: GE 107 wont start up - by morzh - 06-11-2016, 12:15 PM

RE: GE 107 wont start up - by Tgace459 - 06-11-2016, 01:51 PM

RE: GE 107 wont start up - by morzh - 06-11-2016, 02:49 PM

RE: GE 107 wont start up - by Tgace459 - 06-11-2016, 02:58 PM

RE: GE 107 wont start up - by gregb - 06-11-2016, 12:54 PM

RE: GE 107 wont start up - by Tgace459 - 06-11-2016, 01:40 PM

RE: GE 107 wont start up - by morzh - 06-11-2016, 01:00 PM

RE: GE 107 wont start up - by Tgace459 - 06-11-2016, 02:08 PM

RE: GE 107 wont start up - by morzh - 06-11-2016, 03:28 PM

RE: GE 107 wont start up - by Tgace459 - 06-11-2016, 05:03 PM

RE: GE 107 wont start up - by gregb - 06-11-2016, 05:12 PM

RE: GE 107 wont start up - by Tgace459 - 06-13-2016, 12:28 PM

RE: GE 107 wont start up - by Tgace459 - 06-13-2016, 12:51 PM

RE: GE 107 wont start up - by Radioroslyn - 06-13-2016, 01:29 PM

RE: GE 107 wont start up - by Tgace459 - 06-13-2016, 03:15 PM

RE: GE 107 wont start up - by Radioroslyn - 06-13-2016, 04:50 PM

RE: GE 107 wont start up - by Tgace459 - 06-13-2016, 05:07 PM

RE: GE 107 wont start up - by Radioroslyn - 06-13-2016, 05:25 PM

RE: GE 107 wont start up - by Tgace459 - 06-13-2016, 05:31 PM

RE: GE 107 wont start up - by Radioroslyn - 06-13-2016, 05:44 PM

RE: GE 107 wont start up - by Tgace459 - 06-13-2016, 10:19 PM

RE: GE 107 wont start up - by Tgace459 - 06-15-2016, 09:31 AM

RE: GE 107 wont start up - by Radioroslyn - 06-15-2016, 10:04 AM

RE: GE 107 wont start up - by Tgace459 - 06-15-2016, 01:04 PM

RE: GE 107 wont start up - by Radioroslyn - 06-15-2016, 03:14 PM

RE: GE 107 wont start up - by Tgace459 - 06-15-2016, 03:47 PM

RE: GE 107 wont start up - by gregb - 06-15-2016, 07:25 PM

RE: GE 107 wont start up - by Tgace459 - 06-16-2016, 05:33 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 6048 online users. [Complete List]
» 1 Member(s) | 6047 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me