Philco 90

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 90

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

06-27-2016, 01:35 PM

...ummm...actually...

There is no shield (divider) between the group of four tubes (one 27, two 45s, one 80) in the early version of the 90.

Jeff has an earlier version of the "mid" production 90 (1-47). The earlier production models of the 1-47 model 90 have a tubular shield surrounding one of the 27 tubes; later production of the 1-47 chassis has a flat metal plate between two of the four tubes. The 2-47 (late) version also has the flat metal plate.

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 90 - by PhilcoPhan1936 - 06-26-2016, 08:44 PM

RE: Philco 90 - by Eliot Ness - 06-26-2016, 09:42 PM

RE: Philco 90 - by PhilcoPhan1936 - 06-27-2016, 12:32 AM

RE: Philco 90 - by Radioroslyn - 06-26-2016, 11:11 PM

RE: Philco 90 - by PhilcoPhan1936 - 06-27-2016, 12:35 AM

RE: Philco 90 - by markmokris - 06-28-2016, 03:31 PM

RE: Philco 90 - by morzh - 06-27-2016, 11:59 AM

RE: Philco 90 - by Radioroslyn - 06-27-2016, 12:59 PM

RE: Philco 90 - by PhilcoPhan1936 - 06-27-2016, 08:10 PM

RE: Philco 90 - by Radioroslyn - 06-27-2016, 12:53 PM

RE: Philco 90 - by PhilcoPhan1936 - 06-27-2016, 08:08 PM

RE: Philco 90 - by Ron Ramirez - 06-27-2016, 01:35 PM

RE: Philco 90 - by PhilcoPhan1936 - 06-27-2016, 08:04 PM

RE: Philco 90 - by morzh - 06-27-2016, 10:45 PM

RE: Philco 90 - by Radioroslyn - 06-28-2016, 06:42 PM

RE: Philco 90 - by markmokris - 06-29-2016, 04:15 PM

RE: Philco 90 - by Eliot Ness - 06-29-2016, 04:39 PM

RE: Philco 90 - by markmokris - 06-29-2016, 06:06 PM

RE: Philco 90 - by Eliot Ness - 06-29-2016, 10:12 PM

RE: Philco 90 - by markmokris - 06-29-2016, 11:13 PM

RE: Philco 90 - by PhilcoPhan1936 - 06-30-2016, 04:11 PM

RE: Philco 90 - by markmokris - 07-01-2016, 09:32 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

Who's Online

There are currently 3762 online users. [Complete List]
» 4 Member(s) | 3758 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me