Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

I don't believe it!
#8

kruc Wrote:Good find on those dried out caps there Chris. The internet is your friend when looking for unusual caps like you have in that chassis. AES, Digikey, Mouser, All Electronics, Fair Radio, Surplus Sales of Nebraska, and others I'm brainfarting about right now. Also there might be a yayhoo group dedicated to old Marantz gear. Just remember that electrolytic caps are polarized and will vent or explode if wired in reverse. Put a piece of tape or some other marker like a tie wrap to mark the positive lead. A lot of people have learned this the hard way.
Dave
These I think are going to be hard to nail down because they are super skinny and tall and fit into holder compartments! Wish me luck.

tractorforum.com *** I reserve the right to be wrong


Messages In This Thread
I don't believe it! - by Music in a bottle - 07-12-2009, 09:22 PM
Re: I don't believe it! - by Texasrocker - 07-13-2009, 02:19 AM
Re: I don't believe it! - by Music in a bottle - 07-13-2009, 01:23 PM
Re: I don't believe it! - by Arran - 07-13-2009, 11:29 PM
Re: I don't believe it! - by kruc - 07-15-2009, 03:02 AM
Re: I don't believe it! - by Texasrocker - 07-16-2009, 02:01 AM
Re: I don't believe it! - by Music in a bottle - 07-19-2009, 04:37 PM
Re: I don't believe it! - by Music in a bottle - 07-19-2009, 04:39 PM
Re: I don't believe it! - by codefox1 - 07-19-2009, 04:54 PM
Re: I don't believe it! - by Music in a bottle - 07-19-2009, 09:37 PM
Re: I don't believe it! - by kruc - 07-20-2009, 04:07 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4032 online users. [Complete List]
» 3 Member(s) | 4029 Guest(s)
AvatarAvatarAvatar

>