GE Model A-64

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

GE Model A-64

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

07-03-2016, 08:18 PM

Ok Thanks for the response. I will go back to store tomorrow and take a few pictures to see what condition its in.. Maybe offer less to see if they take it.. Are they easy or hard to work on?

Do you happen to have better schematics and or paper work than I was able to get from Riders?

Skip...

Find

« Next Oldest | Next Newest »

Messages In This Thread

GE Model A-64 - by vecher - 07-03-2016, 03:43 PM

RE: GE Model A-64 - by Phlogiston - 07-03-2016, 05:59 PM

RE: GE Model A-64 - by vecher - 07-03-2016, 08:18 PM

RE: GE Model A-64 - by Radioroslyn - 07-03-2016, 10:29 PM

RE: GE Model A-64 - by vecher - 07-03-2016, 10:44 PM

RE: GE Model A-64 - by Arran - 07-04-2016, 04:40 AM

RE: GE Model A-64 - by Phlogiston - 07-04-2016, 10:09 AM

RE: GE Model A-64 - by vecher - 07-04-2016, 10:42 AM

RE: GE Model A-64 - by Kenneth F. Besso Jr. - 07-04-2016, 01:59 PM

RE: GE Model A-64 - by vecher - 07-04-2016, 02:34 PM

RE: GE Model A-64 - by vecher - 07-04-2016, 03:17 PM

RE: GE Model A-64 - by KCMike - 07-04-2016, 04:05 PM

RE: GE Model A-64 - by vecher - 07-04-2016, 04:14 PM

RE: GE Model A-64 - by KCMike - 07-04-2016, 05:03 PM

RE: GE Model A-64 - by vecher - 07-04-2016, 06:10 PM

RE: GE Model A-64 - by vecher - 07-05-2016, 01:43 PM

RE: GE Model A-64 - by Phlogiston - 07-05-2016, 04:59 PM

RE: GE Model A-64 - by vecher - 07-05-2016, 06:03 PM

RE: GE Model A-64 - by Phlogiston - 07-06-2016, 11:35 AM

RE: GE Model A-64 - by Arran - 07-06-2016, 04:05 AM

RE: GE Model A-64 - by vecher - 07-06-2016, 12:22 PM

RE: GE Model A-64 - by vecher - 07-07-2016, 09:02 AM

RE: GE Model A-64 - by Arran - 07-10-2016, 05:02 AM

RE: GE Model A-64 - by vecher - 07-10-2016, 08:55 AM

RE: GE Model A-64 - by Arran - 07-12-2016, 04:14 AM

RE: GE Model A-64 - by vecher - 07-12-2016, 11:54 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 6029 online users. [Complete List]
» 1 Member(s) | 6028 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me