Shadow Meter Question

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Shadow Meter Question

Radioroslyn
Phorum Expert

Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

07-04-2016, 07:12 AM

So I'm assuming that you have to remove the phonalic wafer from the back side of the coil. It looks like it's held on by 5 little brass tabs. Mine are sort of inbeded into the wafer. Was thinking that it might be easier to grind them down a bit and use a little glue at reassembly.
So you didn't take any parts from center of the coil? Like the vane and such? If you didn't what good did the washer do as you couldn't put the bolt though center of the coil? I'm missing something.

Tnx!
Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Shadow Meter Question - by Radioroslyn - 06-27-2016, 07:46 PM

RE: Shadow Meter Question - by morzh - 06-27-2016, 10:47 PM

RE: Shadow Meter Question - by Radioroslyn - 06-27-2016, 11:01 PM

RE: Shadow Meter Question - by morzh - 06-28-2016, 02:52 PM

RE: Shadow Meter Question - by Stan the Man - 06-30-2016, 03:25 PM

RE: Shadow Meter Question - by quartermilecamel - 07-03-2016, 11:20 PM

RE: Shadow Meter Question - by Radioroslyn - 07-04-2016, 07:12 AM

RE: Shadow Meter Question - by KCMike - 07-04-2016, 08:15 AM

RE: Shadow Meter Question - by Radioroslyn - 07-04-2016, 02:31 PM

View a Printable Version

Users browsing this thread: 5 Guest(s)

Recent Posts
Rusty Tuning Condenser
Give the tuner a good wash in Dawn and hot water. Then set tuner in a plastic container and cover with vinegar let soak ...David — 12:53 PM
Rusty Tuning Condenser
If you have rust between the vanes, I wonder how you get the NJ in between, and how you then wipe it off.morzh — 12:02 PM
Philco 60 Squealing
If the noise is still there, the OPT might just be OK. Or so we hope.morzh — 12:01 PM
Philco 60 Squealing
You would probably be replacing the OPT.RodB — 10:54 AM
Philco 60 Squealing
I have been playing the radio for a while now and doing well. Turned it on today and all I got was a whole lot of noise....dconant — 09:39 AM
Rusty Tuning Condenser
Thanks guys. I think I'll give the Naval Jelly a try since I can better control where it goes.dconant — 09:23 AM
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me