GE Model A-64

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

GE Model A-64

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

#22

07-07-2016, 09:02 AM

A couple of questions. What are the Transformer voltages supposed to be? There doesn't seem to be a any voltages on the schematic per-say.. My guess would be about 350-400 volts Ctr taped. A 6.3 volt for the filaments and 5 Volts for the 5Z4..

The cap connected to output is rated at 400 Volts so I assume the voltage is less than that..

Anyway I will go today to see what they will take for it..

Thanks all..

Skip...

Find

« Next Oldest | Next Newest »

Messages In This Thread

GE Model A-64 - by vecher - 07-03-2016, 03:43 PM

RE: GE Model A-64 - by Phlogiston - 07-03-2016, 05:59 PM

RE: GE Model A-64 - by vecher - 07-03-2016, 08:18 PM

RE: GE Model A-64 - by Radioroslyn - 07-03-2016, 10:29 PM

RE: GE Model A-64 - by vecher - 07-03-2016, 10:44 PM

RE: GE Model A-64 - by Arran - 07-04-2016, 04:40 AM

RE: GE Model A-64 - by Phlogiston - 07-04-2016, 10:09 AM

RE: GE Model A-64 - by vecher - 07-04-2016, 10:42 AM

RE: GE Model A-64 - by Kenneth F. Besso Jr. - 07-04-2016, 01:59 PM

RE: GE Model A-64 - by vecher - 07-04-2016, 02:34 PM

RE: GE Model A-64 - by vecher - 07-04-2016, 03:17 PM

RE: GE Model A-64 - by KCMike - 07-04-2016, 04:05 PM

RE: GE Model A-64 - by vecher - 07-04-2016, 04:14 PM

RE: GE Model A-64 - by KCMike - 07-04-2016, 05:03 PM

RE: GE Model A-64 - by vecher - 07-04-2016, 06:10 PM

RE: GE Model A-64 - by vecher - 07-05-2016, 01:43 PM

RE: GE Model A-64 - by Phlogiston - 07-05-2016, 04:59 PM

RE: GE Model A-64 - by vecher - 07-05-2016, 06:03 PM

RE: GE Model A-64 - by Phlogiston - 07-06-2016, 11:35 AM

RE: GE Model A-64 - by Arran - 07-06-2016, 04:05 AM

RE: GE Model A-64 - by vecher - 07-06-2016, 12:22 PM

RE: GE Model A-64 - by vecher - 07-07-2016, 09:02 AM

RE: GE Model A-64 - by Arran - 07-10-2016, 05:02 AM

RE: GE Model A-64 - by vecher - 07-10-2016, 08:55 AM

RE: GE Model A-64 - by Arran - 07-12-2016, 04:14 AM

RE: GE Model A-64 - by vecher - 07-12-2016, 11:54 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me