Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Seeking Woodworking Advice
#6

(07-14-2016, 07:07 AM)OldRestorer Wrote:  Real neat!
 The Majestic 72 took a ride on the Hindenburg and was the first radio used in Zepplins...

Why does the veneer need replacing? If you just strip and refinish the top then you should be fine.. I dont see any damage to the original veneer...

Kirk

Kirk
  That's the Graf Zeppelin, not the Hindenburg, the Graf Zeppelin was built in the 1920s and was famous for circumnavigating the globe, hence why Grigsby-Grunow got involved as a publicity gimmick to promote their radios.
Regards
Arran


Messages In This Thread
Seeking Woodworking Advice - by Winky Dink - 07-14-2016, 04:23 AM
RE: Seeking Woodworking Advice - by Arran - 07-14-2016, 05:49 AM
RE: Seeking Woodworking Advice - by OldRestorer - 07-14-2016, 07:07 AM
RE: Seeking Woodworking Advice - by Arran - 07-15-2016, 04:40 AM
RE: Seeking Woodworking Advice - by Winky Dink - 07-14-2016, 10:23 AM
RE: Seeking Woodworking Advice - by Arran - 07-15-2016, 04:45 AM
RE: Seeking Woodworking Advice - by Dan Walker - 07-14-2016, 11:01 AM
RE: Seeking Woodworking Advice - by Winky Dink - 07-15-2016, 06:45 PM
RE: Seeking Woodworking Advice - by SteveG - 07-15-2016, 06:52 PM
RE: Seeking Woodworking Advice - by klondike98 - 07-15-2016, 07:03 PM
RE: Seeking Woodworking Advice - by Winky Dink - 07-24-2016, 11:16 PM
RE: Seeking Woodworking Advice - by Arran - 07-25-2016, 02:50 AM
RE: Seeking Woodworking Advice - by klondike98 - 07-25-2016, 07:59 AM
RE: Seeking Woodworking Advice - by Winky Dink - 07-25-2016, 12:23 PM
RE: Seeking Woodworking Advice - by klondike98 - 07-25-2016, 12:27 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>