Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Seeking Woodworking Advice
#11

Very Nice carving JOB,,,must have sore fingers,,holding that small item,,,Cheers to ya


Messages In This Thread
Seeking Woodworking Advice - by Winky Dink - 07-14-2016, 04:23 AM
RE: Seeking Woodworking Advice - by Arran - 07-14-2016, 05:49 AM
RE: Seeking Woodworking Advice - by OldRestorer - 07-14-2016, 07:07 AM
RE: Seeking Woodworking Advice - by Arran - 07-15-2016, 04:40 AM
RE: Seeking Woodworking Advice - by Winky Dink - 07-14-2016, 10:23 AM
RE: Seeking Woodworking Advice - by Arran - 07-15-2016, 04:45 AM
RE: Seeking Woodworking Advice - by Dan Walker - 07-14-2016, 11:01 AM
RE: Seeking Woodworking Advice - by Winky Dink - 07-15-2016, 06:45 PM
RE: Seeking Woodworking Advice - by SteveG - 07-15-2016, 06:52 PM
RE: Seeking Woodworking Advice - by klondike98 - 07-15-2016, 07:03 PM
RE: Seeking Woodworking Advice - by Kenneth F. Besso Jr. - 07-15-2016, 08:16 PM
RE: Seeking Woodworking Advice - by Winky Dink - 07-24-2016, 11:16 PM
RE: Seeking Woodworking Advice - by Arran - 07-25-2016, 02:50 AM
RE: Seeking Woodworking Advice - by klondike98 - 07-25-2016, 07:59 AM
RE: Seeking Woodworking Advice - by Winky Dink - 07-25-2016, 12:23 PM
RE: Seeking Woodworking Advice - by klondike98 - 07-25-2016, 12:27 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5415 online users. [Complete List]
» 2 Member(s) | 5413 Guest(s)
AvatarAvatar

>