Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA R-8 Chassis Rebuild
#6

 They aren't that bad, I've worked on a couple of these, and will work on a couple more that are in the restoration docket. One was a C.G.E J-82 and the other a Canadian Westinghouse 801 Columaire which uses similar circuitry and components but in a Westinghouse built chassis, the next two will be another J-82, and an S-42A. The biggest nuisance isn't the tuning condenser it's the IF cans and the oscillator coil, which you may or may not have to remove to get at some things. These sets are good performers though, which probably explains why there are so many survivors as they were probably good sellers.
Regards
Arran


Messages In This Thread
RCA R-8 Chassis Rebuild - by Phlogiston - 07-15-2016, 10:48 AM
RE: RCA R-8 Chassis Rebuild - by KCMike - 07-15-2016, 12:16 PM
RE: RCA R-8 Chassis Rebuild - by Eliot Ness - 07-15-2016, 03:17 PM
RE: RCA R-8 Chassis Rebuild - by klondike98 - 07-15-2016, 07:05 PM
RE: RCA R-8 Chassis Rebuild - by Paul Philco322 - 07-15-2016, 09:27 PM
RE: RCA R-8 Chassis Rebuild - by Arran - 07-16-2016, 04:22 AM
RE: RCA R-8 Chassis Rebuild - by Phlogiston - 07-16-2016, 11:03 AM
RE: RCA R-8 Chassis Rebuild - by palegreenthumb - 07-16-2016, 04:28 AM
RE: RCA R-8 Chassis Rebuild - by Phlogiston - 07-16-2016, 10:57 AM
RE: RCA R-8 Chassis Rebuild - by Arran - 07-18-2016, 03:13 AM
RE: RCA R-8 Chassis Rebuild - by Phlogiston - 07-18-2016, 11:01 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5531 online users. [Complete List]
» 1 Member(s) | 5530 Guest(s)
Avatar

>