1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 42-PT-2 candohm
brotherfan
New Member
*
Posts: 1
Threads: 1
Joined: Jul 2016
City: Benwood, WV
#1

07-22-2016, 09:29 PM
If you look at the schematic for the Philco PT-2 the candohm lugs, part 27, should NOT have a resistance path to the chassis, correct? I get about a 3 to 4 meg ohm resistance reading at each of the 3 lugs and the chassis, but this shouldn't be, right? I'm going to rebuild it anyway, but I just want to confirm my thoughts that any connection to ground shouldn't be at those lugs.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 42-PT-2 candohm - by brotherfan - 07-22-2016, 09:29 PM
RE: Philco 42-PT-2 candohm - by klondike98 - 07-22-2016, 10:03 PM
RE: Philco 42-PT-2 candohm - by Radioroslyn - 07-22-2016, 10:31 PM
RE: Philco 42-PT-2 candohm - by morzh - 07-22-2016, 11:16 PM
RE: Philco 42-PT-2 candohm - by Arran - 07-22-2016, 11:56 PM
RE: Philco 42-PT-2 candohm - by klondike98 - 07-23-2016, 08:42 AM
RE: Philco 42-PT-2 candohm - by codefox1 - 08-06-2016, 08:57 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Oscillation
Will do, thank you.tludka — 10:26 AM
Philco 38-7 Oscillation
As to your oscillation issue I would align the IF transformers. That may solve the problem. You also would want to check...Radioroslyn — 10:22 AM
Philco 38-7 Speaker
Thank you, I will check this out, I do have some shields I can place around the specific tubes. I searched the four que...tludka — 10:18 AM
Philco 38-7 Speaker
Also, check if any wires going to Grid Caps of the tubes that are supposed to be INSIDE of their respective shields (if ...morzh — 09:54 AM
Philco 38-7 Oscillation
Usually in this forum, when we discuss a radio, we do not multiply threads. You already have a thread on this. If you wa...morzh — 09:27 AM
identify very thin wire for replacement on 37-640
You can possibly use a heatshrink tubing. If you decide to replace the wire, anything gauge 24, 300V rated will do (it ...morzh — 09:25 AM
identify very thin wire for replacement on 37-640
Happy Thanksgiving,  I have attche a photo of a very thin wire with black plastic-looking insulation(some of it has com...georgetownjohn — 09:14 AM
Philco 60 Squealing
I got my signal tracer out to see if I could tell at what stage the squeal was coming from. It is present on the plate o...dconant — 09:07 AM
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM

[-]
Who's Online
There are currently 1902 online users. [Complete List]
» 3 Member(s) | 1899 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration