1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 42-PT-2 candohm
Kenneth F. Besso Jr.
Senior Member
****
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
#7

07-23-2016, 04:55 PM
just had one in a Emerson 59 Ch--- 2 taps on it,,,read 500 ohms,,,,here it was short out to the frame of the resistor,,,didn't figure it out till ,,I took the leds off to check it,,this one was bolted to the chassis,,,Cheers
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 42-PT-2 candohm - by brotherfan - 07-22-2016, 09:29 PM
RE: Philco 42-PT-2 candohm - by klondike98 - 07-22-2016, 10:03 PM
RE: Philco 42-PT-2 candohm - by Radioroslyn - 07-22-2016, 10:31 PM
RE: Philco 42-PT-2 candohm - by morzh - 07-22-2016, 11:16 PM
RE: Philco 42-PT-2 candohm - by Arran - 07-22-2016, 11:56 PM
RE: Philco 42-PT-2 candohm - by klondike98 - 07-23-2016, 08:42 AM
RE: Philco 42-PT-2 candohm - by Kenneth F. Besso Jr. - 07-23-2016, 04:55 PM
RE: Philco 42-PT-2 candohm - by codefox1 - 08-06-2016, 08:57 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Oscillation
Will do, thank you.tludka — 10:26 AM
Philco 38-7 Oscillation
As to your oscillation issue I would align the IF transformers. That may solve the problem. You also would want to check...Radioroslyn — 10:22 AM
Philco 38-7 Speaker
Thank you, I will check this out, I do have some shields I can place around the specific tubes. I searched the four que...tludka — 10:18 AM
Philco 38-7 Speaker
Also, check if any wires going to Grid Caps of the tubes that are supposed to be INSIDE of their respective shields (if ...morzh — 09:54 AM
Philco 38-7 Oscillation
Usually in this forum, when we discuss a radio, we do not multiply threads. You already have a thread on this. If you wa...morzh — 09:27 AM
identify very thin wire for replacement on 37-640
You can possibly use a heatshrink tubing. If you decide to replace the wire, anything gauge 24, 300V rated will do (it ...morzh — 09:25 AM
identify very thin wire for replacement on 37-640
Happy Thanksgiving,  I have attche a photo of a very thin wire with black plastic-looking insulation(some of it has com...georgetownjohn — 09:14 AM
Philco 60 Squealing
I got my signal tracer out to see if I could tell at what stage the squeal was coming from. It is present on the plate o...dconant — 09:07 AM
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM

[-]
Who's Online
There are currently 4060 online users. [Complete List]
» 2 Member(s) | 4058 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration