Philco 89 (123) (Update-Coil rewind)

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 89 (123) (Update-Coil rewind)

exray
Phorum Expert

Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA State, Province, Country: PR

08-03-2009, 12:22 AM

gary rabbitt Wrote:HI Bill,
Good to see you

I have a set of Riders, so I will look in related pages for the osc coil issue. I didn't see it off hand with the model 89 (123) diagrams.=

Its in there. All about drying the coil and resealing it and fudging the cathode R values. That was a CENSORED after a year or two of coming off the assembly line. Imagine 70 years later!
89 is a good radio but they seem to require some intuitive savvy to get them back to par.

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 89 (123) (Update-Coil rewind) - by gary rabbitt - 08-01-2009, 09:55 PM

Re: Philco 89 (123) Early run, wrong tube? - by Texasrocker - 08-01-2009, 10:48 PM

Re: Philco 89 (123) Early run, wrong tube? - by Steve Chambers - 08-02-2009, 08:09 AM

Re: Philco 89 (123) Early run, wrong tube? - by Ron Ramirez - 08-02-2009, 09:56 AM

Re: Philco 89 (123) Early run, wrong tube? - by Ron Ramirez - 08-02-2009, 10:03 AM

Re: Philco 89 (123) Early run, wrong tube? - by gary rabbitt - 08-02-2009, 03:08 PM

Re: Philco 89 (123) Early run, wrong tube? - by exray - 08-02-2009, 05:25 PM

Re: Philco 89 (123) Early run, wrong tube? - by gary rabbitt - 08-02-2009, 09:56 PM

Re: Philco 89 (123) Early run, wrong tube? - by exray - 08-03-2009, 12:22 AM

Re: Philco 89 (123) Early run, wrong tube? - by gary rabbitt - 08-05-2009, 04:56 PM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by exray - 08-06-2009, 05:29 AM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by gary rabbitt - 08-06-2009, 11:59 AM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by exray - 08-06-2009, 01:56 PM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by Texasrocker - 08-09-2009, 12:53 AM

Re: Philco 89 (123) UPDATE/Coil rewind? - by gary rabbitt - 08-14-2009, 11:34 PM

Re: Philco 89 (123) UPDATE/Coil rewind? - by Ron Ramirez - 08-15-2009, 10:16 AM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by gary rabbitt - 08-15-2009, 11:46 AM

Re: Philco 89 (123) (Update-Coil rewind) - by gary rabbitt - 08-16-2009, 08:48 PM

View a Printable Version

Users browsing this thread:

Recent Posts
Correct model 84 Ac plug an cord type
From what I read Philco went to using brown rubber power cords in 1936, so cloth was used in the 1935 and earlier models...Arran — 11:25 PM
Correct model 84 Ac plug an cord type
Hi Bruce, I have not worked on an 84, but in general, power cords for almost any radio prior to 1938 was cloth covered...MrFixr55 — 08:34 PM
Restoring Philco 38-14
OK, well, so after staring at the sch again, I realized the problem had to be the #12/12A padder. I put a scope on the o...morzh — 08:15 PM
Correct model 84 Ac plug an cord type
Hello Bruce, I mostly use brown far as my cloth powercords go ! Here is the plug that I have used bakelite Acorn style...radiorich — 08:05 PM
Correct model 84 Ac plug an cord type
Looking for as correct as can find the right Ac plug an the correct colored cloth line. Ive seen many old photos but mos...Bruce — 04:13 PM
Restoring Philco 38-14
Rod Two Y-caps make sense if you use them from L/N to the chassis; this is only makes sense in the transformer radios...morzh — 10:11 AM
Restoring Philco 38-14
Mike, I'm curious about a specific use of he Y cap. Lately I've seen a single cap across the power transformer primary. ...RodB — 09:01 AM
Restoring Philco 38-14
hello morzh , That sounds like a plan ! Sincerely Richardradiorich — 07:45 AM
Restoring Philco 38-14
Richard, It helped some, but I still had the whining when engaging the rear power strip (I did not realize it was fro...morzh — 07:07 AM
Restoring Philco 38-14
Hello morzh, Yes , that dreaded hum in my room where i do alighment I have my cable modem and router plus desktop plus ...radiorich — 11:25 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me