Philco 37-650

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 37-650

Oldresistor47
Junior Member

Posts: 27
Threads: 4
Joined: Aug 2016
City: Pembroke Pines, FL

08-07-2016, 06:02 PM

(08-06-2016, 10:22 PM)Oldresistor47 Wrote: I'm new to this site. I need help on locating the on/off, tone control pot for this Philco model. The tone portion is not working properly and the on/off metal piece is fatigued. After changing electrolytics, it still draws too much current. It'll play fine at 110 volts. House current is usually 123. Any suggestions or should I install a limiting resistor? Thanks

Thank you. Did try a new pot but it wasn't right. Reinstalled old one, crossing my fingers the metal catch for the off side of switch holds, while I locate one. I understand lixdeslia.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 37-650 - by Oldresistor47 - 08-06-2016, 10:22 PM

RE: Philco 37-650 - by Radioroslyn - 08-07-2016, 08:53 AM

RE: Philco 37-650 - by klondike98 - 08-07-2016, 10:14 AM

RE: Philco 37-650 - by Oldresistor47 - 08-07-2016, 06:02 PM

RE: Philco 37-650 - by Radioroslyn - 08-08-2016, 07:23 PM

RE: Philco 37-650 - by Oldresistor47 - 08-07-2016, 06:06 PM

RE: Philco 37-650 - by morzh - 08-07-2016, 06:30 PM

RE: Philco 37-650 - by Oldresistor47 - 08-07-2016, 07:26 PM

RE: Philco 37-650 - by morzh - 08-07-2016, 08:32 PM

RE: Philco 37-650 - by Oldresistor47 - 08-08-2016, 07:24 AM

RE: Philco 37-650 - by Oldresistor47 - 08-08-2017, 06:46 PM

RE: Philco 37-650 - by Oldresistor47 - 08-17-2017, 09:06 PM

RE: Philco 37-650 - by Radioroslyn - 08-17-2017, 10:10 PM

RE: Philco 37-650 - by Oldresistor47 - 08-18-2017, 05:31 AM

RE: Philco 37-650 - by Radioroslyn - 08-18-2017, 11:51 AM

RE: Philco 37-650 - by Oldresistor47 - 08-18-2017, 09:31 PM

RE: Philco 37-650 - by Oldresistor47 - 01-09-2018, 10:34 PM

RE: Philco 37-650 - by Radioroslyn - 01-09-2018, 10:48 PM

RE: Philco 37-650 - by Oldresistor47 - 01-24-2018, 08:14 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
Philco Predicta Siesta picture over time getting dimmer
I found that the wire insulation was burnt. The fly back needs corona dope! Why would someone put that there?Platinumblonde36 — 01:09 AM
Philco Predicta Siesta picture over time getting dimmer
This is what it looked like beforePlatinumblonde36 — 01:01 AM
Philco Predicta Siesta picture over time getting dimmer
Platinumblonde36 — 12:58 AM
Philco Predicta Siesta picture over time getting dimmer
Platinumblonde36 — 12:57 AM
Philco Predicta Siesta picture over time getting dimmer
I'm finding some strange things in my set and for the most part it's also original, so I need to start going over everyt...Platinumblonde36 — 12:55 AM

Who's Online

There are currently 5179 online users. [Complete List]
» 1 Member(s) | 5178 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me