Philco 89 (123) (Update-Coil rewind)

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 89 (123) (Update-Coil rewind)

exray
Phorum Expert

Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA State, Province, Country: PR

#11

08-06-2009, 06:29 AM

Hi again Gary,
You can estimate the current thru the resistor from the schematic and calculate the wattage. Its not terribly high. They used wirewound so as to obtain the precise values that weren't available in a normal carbon resistor.

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 89 (123) (Update-Coil rewind) - by gary rabbitt - 08-01-2009, 10:55 PM

Re: Philco 89 (123) Early run, wrong tube? - by Texasrocker - 08-01-2009, 11:48 PM

Re: Philco 89 (123) Early run, wrong tube? - by Steve Chambers - 08-02-2009, 09:09 AM

Re: Philco 89 (123) Early run, wrong tube? - by Ron Ramirez - 08-02-2009, 10:56 AM

Re: Philco 89 (123) Early run, wrong tube? - by Ron Ramirez - 08-02-2009, 11:03 AM

Re: Philco 89 (123) Early run, wrong tube? - by gary rabbitt - 08-02-2009, 04:08 PM

Re: Philco 89 (123) Early run, wrong tube? - by exray - 08-02-2009, 06:25 PM

Re: Philco 89 (123) Early run, wrong tube? - by gary rabbitt - 08-02-2009, 10:56 PM

Re: Philco 89 (123) Early run, wrong tube? - by exray - 08-03-2009, 01:22 AM

Re: Philco 89 (123) Early run, wrong tube? - by gary rabbitt - 08-05-2009, 05:56 PM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by exray - 08-06-2009, 06:29 AM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by gary rabbitt - 08-06-2009, 12:59 PM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by exray - 08-06-2009, 02:56 PM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by Texasrocker - 08-09-2009, 01:53 AM

Re: Philco 89 (123) UPDATE/Coil rewind? - by gary rabbitt - 08-15-2009, 12:34 AM

Re: Philco 89 (123) UPDATE/Coil rewind? - by Ron Ramirez - 08-15-2009, 11:16 AM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by gary rabbitt - 08-15-2009, 12:46 PM

Re: Philco 89 (123) (Update-Coil rewind) - by gary rabbitt - 08-16-2009, 09:48 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5583 online users. [Complete List]
» 1 Member(s) | 5582 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me