Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

610 Chassis Restoration
#4

(08-14-2016, 09:39 PM)Radioroslyn Wrote:  
(08-14-2016, 09:00 PM)morzh Wrote:  Looks clean. What did you use or do?

Has that wire wheel on a drill look about it.

That is the way the wax polishes out. I can remove it partially, or totally and rework the look.
A lot of what you see is the camera effect. In real life, it is shiny, but still has that "antique" finish.
To me, it is better than spray paint, but not as good as re-plating.
I used the little toothbrush size brushes that come in a three pack at homerepo to get the rust off.


Messages In This Thread
610 Chassis Restoration - by kc5gym - 08-14-2016, 08:53 PM
RE: 610 Chassis Restoration - by morzh - 08-14-2016, 09:00 PM
RE: 610 Chassis Restoration - by Radioroslyn - 08-14-2016, 09:39 PM
RE: 610 Chassis Restoration - by kc5gym - 08-14-2016, 09:47 PM
RE: 610 Chassis Restoration - by Paul Philco322 - 08-15-2016, 08:18 PM
RE: 610 Chassis Restoration - by kc5gym - 08-15-2016, 08:56 PM
RE: 610 Chassis Restoration - by kc5gym - 08-15-2016, 08:59 PM
RE: 610 Chassis Restoration - by Radioroslyn - 08-15-2016, 09:17 PM
RE: 610 Chassis Restoration - by kc5gym - 08-15-2016, 09:36 PM
RE: 610 Chassis Restoration - by kc5gym - 08-15-2016, 09:42 PM
RE: 610 Chassis Restoration - by Radioroslyn - 08-15-2016, 09:59 PM
RE: 610 Chassis Restoration - by kc5gym - 08-15-2016, 10:11 PM
RE: 610 Chassis Restoration - by IowaPhilco - 08-17-2016, 12:59 AM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Rusty Tuning Condenser
Give the tuner a good wash in Dawn and hot water. Then set tuner in a plastic container and cover with vinegar let soak ...David — 12:53 PM
Rusty Tuning Condenser
If you have rust between the vanes, I wonder how you get the NJ in between, and how you then wipe it off.morzh — 12:02 PM
Philco 60 Squealing
If the noise is still there, the OPT might just be OK. Or so we hope.morzh — 12:01 PM
Philco 60 Squealing
You would probably be replacing the OPT.RodB — 10:54 AM
Philco 60 Squealing
I have been playing the radio for a while now and doing well. Turned it on today and all I got was a whole lot of noise....dconant — 09:39 AM
Rusty Tuning Condenser
Thanks guys. I think I'll give the Naval Jelly a try since I can better control where it goes.dconant — 09:23 AM
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM

[-]
Who's Online
There are currently 3851 online users. [Complete List]
» 1 Member(s) | 3850 Guest(s)
Avatar

>