1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
610 Chassis Restoration
Radioroslyn
Phorum Expert
*****
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#9

08-15-2016, 09:17 PM
https://www.amaco.com/t/mixed-media/meta...rub-n-buff

Interesting. Sort of covering up the rust w/wax.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
610 Chassis Restoration - by kc5gym - 08-14-2016, 08:53 PM
RE: 610 Chassis Restoration - by morzh - 08-14-2016, 09:00 PM
RE: 610 Chassis Restoration - by Radioroslyn - 08-14-2016, 09:39 PM
RE: 610 Chassis Restoration - by kc5gym - 08-14-2016, 09:47 PM
RE: 610 Chassis Restoration - by Paul Philco322 - 08-15-2016, 08:18 PM
RE: 610 Chassis Restoration - by kc5gym - 08-15-2016, 08:56 PM
RE: 610 Chassis Restoration - by kc5gym - 08-15-2016, 08:59 PM
RE: 610 Chassis Restoration - by Radioroslyn - 08-15-2016, 09:17 PM
RE: 610 Chassis Restoration - by kc5gym - 08-15-2016, 09:36 PM
RE: 610 Chassis Restoration - by kc5gym - 08-15-2016, 09:42 PM
RE: 610 Chassis Restoration - by Radioroslyn - 08-15-2016, 09:59 PM
RE: 610 Chassis Restoration - by kc5gym - 08-15-2016, 10:11 PM
RE: 610 Chassis Restoration - by IowaPhilco - 08-17-2016, 12:59 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Rusty Tuning Condenser
If you have rust between the vanes, I wonder how you get the NJ in between, and how you then wipe it off.morzh — 12:02 PM
Philco 60 Squealing
If the noise is still there, the OPT might just be OK. Or so we hope.morzh — 12:01 PM
Philco 60 Squealing
You would probably be replacing the OPT.RodB — 10:54 AM
Philco 60 Squealing
I have been playing the radio for a while now and doing well. Turned it on today and all I got was a whole lot of noise....dconant — 09:39 AM
Rusty Tuning Condenser
Thanks guys. I think I'll give the Naval Jelly a try since I can better control where it goes.dconant — 09:23 AM
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM

[-]
Who's Online
There are currently 1617 online users. [Complete List]
» 1 Member(s) | 1616 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration