Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 90 Lowboy
#5

Hi Chris,
Yes older big chassis sets w/ the worm gear in the front and back are a pain to restring. Common issues to pre '36 or so Philcos are open primaries on the rf coils, oscillator coil feedback winding open, fairly rare to find a bad if transformer, open audio driver and sometimes output transformers, spkr field coil open.

Sounds like you've dodged the bullet on most of these but would check the ant coil primary, this might be the cause of the good reception where touching the 24 cap.

GLOM de N3GTE

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco 90 Lowboy - by Chris h - 08-20-2016, 08:23 PM
RE: Philco 90 Lowboy - by markmokris - 08-22-2016, 10:29 AM
RE: Philco 90 Lowboy - by morzh - 08-22-2016, 11:26 PM
RE: Philco 90 Lowboy - by Chris h - 08-23-2016, 08:19 AM
RE: Philco 90 Lowboy - by Radioroslyn - 08-23-2016, 12:27 PM
RE: Philco 90 Lowboy - by Chris h - 08-23-2016, 01:21 PM
RE: Philco 90 Lowboy - by Chris h - 12-14-2016, 01:13 AM
RE: Philco 90 Lowboy - by Chris h - 12-20-2016, 11:00 PM
RE: Philco 90 Lowboy - by morzh - 12-21-2016, 12:40 AM
RE: Philco 90 Lowboy - by Ron Ramirez - 12-21-2016, 12:59 PM
RE: Philco 90 Lowboy - by morzh - 12-21-2016, 02:12 PM
RE: Philco 90 Lowboy - by Chris h - 12-21-2016, 11:21 PM
RE: Philco 90 Lowboy - by morzh - 12-21-2016, 11:29 PM
RE: Philco 90 Lowboy - by Ron Ramirez - 12-22-2016, 07:05 AM
RE: Philco 90 Lowboy - by Chris h - 12-27-2016, 10:58 AM
RE: Philco 90 Lowboy - by Chris h - 12-31-2016, 01:47 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently 6095 online users. [Complete List]
» 1 Member(s) | 6094 Guest(s)
Avatar

>