Philco 89 (123) (Update-Coil rewind)

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 89 (123) (Update-Coil rewind)

gary rabbitt
Senior Member

Posts: 271
Threads: 12
Joined: Nov 2005
City: Nashville, TN

#17

08-15-2009, 12:46 PM

Thanks Ron.
I will try and rewind it today, it shouldn't be that bad to do.

The other windings look ok, but when I took the inner coil form out, (shouldn't have) I broke one of the wires on that form. I did a micro mini splice to repair that so it should be fine.

I'll let you know how it turns out, and thanks again.
Best regards,
Gary

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 89 (123) (Update-Coil rewind) - by gary rabbitt - 08-01-2009, 10:55 PM

Re: Philco 89 (123) Early run, wrong tube? - by Texasrocker - 08-01-2009, 11:48 PM

Re: Philco 89 (123) Early run, wrong tube? - by Steve Chambers - 08-02-2009, 09:09 AM

Re: Philco 89 (123) Early run, wrong tube? - by Ron Ramirez - 08-02-2009, 10:56 AM

Re: Philco 89 (123) Early run, wrong tube? - by Ron Ramirez - 08-02-2009, 11:03 AM

Re: Philco 89 (123) Early run, wrong tube? - by gary rabbitt - 08-02-2009, 04:08 PM

Re: Philco 89 (123) Early run, wrong tube? - by exray - 08-02-2009, 06:25 PM

Re: Philco 89 (123) Early run, wrong tube? - by gary rabbitt - 08-02-2009, 10:56 PM

Re: Philco 89 (123) Early run, wrong tube? - by exray - 08-03-2009, 01:22 AM

Re: Philco 89 (123) Early run, wrong tube? - by gary rabbitt - 08-05-2009, 05:56 PM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by exray - 08-06-2009, 06:29 AM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by gary rabbitt - 08-06-2009, 12:59 PM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by exray - 08-06-2009, 02:56 PM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by Texasrocker - 08-09-2009, 01:53 AM

Re: Philco 89 (123) UPDATE/Coil rewind? - by gary rabbitt - 08-15-2009, 12:34 AM

Re: Philco 89 (123) UPDATE/Coil rewind? - by Ron Ramirez - 08-15-2009, 11:16 AM

Re: Philco 89 (123) (Wirewound resistor Wattage) - by gary rabbitt - 08-15-2009, 12:46 PM

Re: Philco 89 (123) (Update-Coil rewind) - by gary rabbitt - 08-16-2009, 09:48 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5487 online users. [Complete List]
» 1 Member(s) | 5486 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me